首页 > ATMEL 爱特梅尔 > DataFlash存储器

ATMEL 爱特梅尔串行FLASH 存储器AT45DB081B

AT45DB081B 概述

The AT45DB081B is a 2.5-volt or 2.7-volt only, serial interface Flash memory ideally suited for a wide variety of digital voice-, image-, program code- and data-storage applications. Its 8,650,752 bits of memory are organized as 4096 pages of 264 bytes each. In addition to the main memory, the AT45DB081B also contains two SRAM data buffers of 264 bytes each. The buffers allow receiving of data while a page in the main memory is being reprogrammed, as well as writing a continuous data stream.EEPROM emulation (bit or byte alterability) is easily handled with a self-contained three
step Read-Modify-Write operation. Unlike conventional Flash memories that are accessed randomly with multiple address lines and a parallel interface, the DataFlash uses a SPI serial interface to sequentially access its data. DataFlash supports SPI mode 0 and mode 3. The simple serial interface facilitates hardware layout, increases system reliability, minimizes switching noise, and reduces package size and active pin count.
The device is optimized for use in many commercial and industrial applications where high density, low pin count, low voltage, and low power are essential. The device operates at clock frequencies up to 20 MHz with a typical active read current consumption of 4 mA.To allow for simple in-system reprogrammability, the AT45DB081B does not require high input voltages for programming. The device operates from a single power supply,2.5V to 3.6V or 2.7V to 3.6V, for both the program and read operations. The AT45DB081B is enabled through the chip select pin (CS) and accessed via a three-wire interface consisting of the Serial Input (SI), Serial Output (SO), and the Serial Clock (SCK).All programming cycles are self-timed, and no separate erase cycle is required before
programming.When the device is shipped from Atmel, the most significant page of the memory array
may not be erased. In other words, the contents of the last page may not be filled with FFH.

AT45DB081B 特性

• Single 2.5V - 3.6V or 2.7V - 3.6V Supply
  • Serial Peripheral Interface (SPI) Compatible
  • 20 MHz Max Clock Frequency
  • Page Program Operation
  – Single Cycle Reprogram (Erase and Program)
  – 4096 Pages (264 Bytes/Page) Main Memory
  • Supports Page and Block Erase Operations
  • Two 264-byte SRAM Data Buffers – Allows Receiving of Data
  while Reprogramming of Nonvolatile Memory
  • Continuous Read Capability through Entire Array
  – Ideal for Code Shadowing Applications
  • Low Power Dissipation
  – 4 mA Active Read Current Typical
  – 2 μA CMOS Standby Current Typical
  • Hardware Data Protection Feature
  • 100% Compatible to AT45DB081 and AT45DB081A
  • 5.0V-tolerant Inputs: SI, SCK, CS, RESET and WP Pins
  • Commercial and Industrial Temperature Ranges
  • Green (Pb/Halide-free) Packaging Options

AT45DB081B订购型号

Ordering Code	Package	Lead Finish	Operating Voltage	Max. Freq. (MHz)	Operation Range
AT45DB081B-CC AT45DB081B-CNC AT45DB081B-RC AT45DB081B-TC	14C1 8CN3 28R 28T	-	25V to 3.6V	20	Commercial (0° C to 70° C)
AT45DB081B-CI AT45DB081B-CNI AT45DB081B-RI AT45DB081B-TI	14C1 8CN3 28R 28T	-	25V to 3.6V	20	Industrial (-40°C to +85°C)
AT45DB081B-CC-2.5 AT45DB081B-CNC-2.5 AT45DB081B-RC-2.5 AT45DB081B-TC-2.5	14C1 8CN3 28R 28T	-	25V to 3.6V	15	Commercial (0° C to 70° C)
AT45DB081B-CNU AT45DB081B-RU AT45DB081B-TU AT45DB081B-CU	8CN3 28R 28T 14C1	-	25V to 3.6V	20	Industrial (-40°C to +85°C)