CBTL04DP211BS DisplayPort 2 : 1 multiplexer
CBTL04DP211 is an (Embedded) DisplayPort multiplexer for DisplayPort v1.1a switching and multiplexing applications on PC platforms. It is capable of 1 : 2 switching or 2 : 1 multiplexing of 2-lane DisplayPort Main Link signals, using high-bandwidth pass-gate technology. Also, it can switch/multiplex Hot Plug Detect (HPD) signal and AUX signals, for a total of four channels on the display side.
To facilitate DisplayPort switching/multiplexing scheme on PC platforms suitably, CBTL04DP211 provides two separate selection pins (GPU_SEL, AUX_SEL). The selection pin GPU_SEL performs switching from one Main Link to another Main Link. HPD signals will also be switched using the same selection pin. A separate select pin (AUX_SEL) provides additional selection between two AUX channels such that the AUX channel selection is independent of the Main Link and HPD signal selection.
A typical application of CBTL04DP211 is on motherboards where one of two GPU/CPU display sources needs to be selected to connect to a DisplayPort sink device or connector. A controller chip selects which path to use by setting a select signal HIGH or LOW. Due to the non-directional nature of the signal paths (which use high-bandwidth pass-gate technology), the CBTL04DP211 can also be used in the reverse topology, e.g., to connect one DisplayPort source device to one of two DisplayPort sink devices or connectors
产品特点 Features
- Supports DisplayPort v1.1a: 1.62 Gbit/s, 2.7 Gbit/s
- Supports Embedded DisplayPort v1.2: 1.62 Gbit/s, 2.7 Gbit/s
- Supports 1-lane, 2-lane Main Link operation
- 1 : 2 switching or 2 : 1 multiplexing of DisplayPort Main Link signals
- 2 high-speed differential channels with 2 : 1 multiplexing/switching for DisplayPort Main Link signals
- 1 channel with 2 : 1 multiplexing/switching for AUX signals
- 1 channel with 2 : 1 multiplexing/switching for single-ended HPD signals
- High-bandwidth analog pass-gate technology
- Very low intra-pair differential skew (5 ps typical)
- Very low inter-pair skew (< 180 ps)
- Switch/multiplexer position select CMOS input
- Single 3.3 V power supply
- Very low operation current of 0.2 mA typical
- ESD 8 kV HBM, 1 kV CDM
- ESD 2 kV HBM, 500 V CDM for control pins
- Available in 3 mm × 6 mm, 0.4 mm pitch HVQFN32 package
|
应用
- Motherboard applications requiring (embedded) DisplayPort switching/multiplexing
- Docking stations
- Notebook computers
- Chip sets requiring flexible allocation of DisplayPort I/O pins to board connectors
产品实物图
|
封装
| 型号 |
可订购的器件编号 |
订购码 (12NC) |
产品状态 |
封装 |
| CBTL04DP211BS |
9352 941 12518 |
CBTL04DP211BS,518 |
量产 |
HVQFN32
(SOT1185-1) |
订货和供应
| 型号 |
订购码 (12NC) |
可订购的器件编号 |
化学成分 |
| CBTL04DP211BS |
9352 941 12518 |
CBTL04DP211BS,518 |
CBTL04DP211BS |
CBTL04DP211BS 技术支持
| 档案名称 |
标题 |
类型 |
格式 |
| CBTL04DP211BS |
DisplayPort 2 : 1 multiplexer |
Data sheet |
pdf |
| AN10587 |
Interfacing NXP bridge IC with NXP ARM microcontroller
|
Application note |
pdf |
| AN10417 |
SC16IS760/762 Fast IrDA mode
|
Application note |
pdf |
| AN10428 |
UART-SPI Gateway for Philips SPI slave bridges
|
Application note |
pdf |
| AN10462 |
SPI programming for Philips Bridge ICs
|
Application note |
pdf |
| AN10485 |
SDA pin connection in SPI mode
|
Application note |
pdf |
| AN10486 |
Automatic RS-485 address detection
|
Application note |
pdf |
| AN10571 |
Sleep programming for NXP bridge ICs
|
Application note |
pdf |
| AN10452 |
Interfacing Philips Bridge IC with Philips microcontroller
|
Application note |
pdf |
| 75015676 |
Low-power bridges for I2C or SPI to UART or IrDA or GPIO; NXP low-power bridges SC16IS750/52/60/62
|
Leaflet |
pdf |
