CLRC66301HN High Performance NFC Reader Solution

The CLRC663 is a highly integrated transceiver IC for contactless communication at 13.56 MHz.

The CLRC663 transceiver IC supports the following operating modes:

Read/write mode supporting ISO/IEC 14443A/MIFARE
Read/write mode supporting ISO/IEC 14443B
Read/write mode supporting JIS X 6319-4 (comparable with FeliCa scheme)
Passive initiator mode according to ISO/IEC 18092
Read/write mode supporting ISO/IEC 15693
Read/write mode supporting ICODE EPC UID/ EPC OTP
Read/write mode supporting ISO/IEC 18000-3 mode 3/ EPC Class-1 HF

The CLRC663’s internal transmitter is able to drive a reader/writer antenna designed to communicate with ISO/IEC 14443A/MIFARE cards and transponders without additional active circuitry. The digital module manages the complete ISO/IEC 14443A framing and error detection functionality (parity and CRC).

The CLRC663 supports MIFARE Classic 1K, MIFARE Classic 4K, MIFARE Ultralight, MIFARE Ultralight C, MIFARE PLUS and MIFARE DESFire products. The CLRC663 supports MIFARE higher transfer speeds of up to 848 kbit/s in both directions.

The CLRC663 supports layer 2 and 3 of the ISO/IEC 14443B reader/writer communication scheme except anticollision. The anticollision needs to be implemented in the firmware of the host controller as well as in the upper layers.

The CLRC663 is able to demodulate and decode FeliCa coded signals.The FeliCa receiver part provides the demodulation and decoding circuitry for FeliCa coded signals. The CLRC663 handles the FeliCa framing and error detection such as CRC. The CLRC663 supports FeliCa higher transfer speeds of up to 424 kbit/s in both directions.

The CLRC663 is supporting the P2P passive initiator mode in accordance with ISO/IEC 18092.

The CLRC663 supports the vicinity protocol according to ISO/IEC15693, EPC UID and ISO/IEC 18000-3 mode 3/ EPC Class-1 HF.

The following host interfaces are supported:

Serial Peripheral Interface (SPI)
Serial UART (similar to RS232 with voltage levels dependent on pin voltage supply)
I²C-bus interface (two versions are implemented: I2C and I2CL)

The CLRC663 supports the connection of a secure access module (SAM). A dedicated separate I2C interface is implemented for a connection of the SAM. The SAM can be used for high secure key storage and acts as a very performant crypto coprocessor. A dedicated SAM is available for connection to the CLRC663

产品特点 Features

High RF output power frontend IC for transfer speed up to 848 kbit/s
Supports ISO/IEC 14443 A/MIFARE, ISO/IEC 14443 B and FeliCa
P2P passive initiator mode in accordance with ISO/IEC 18092
Supports ISO/IEC15693, ICODE EPC UID and ISO/IEC 18000-3 mode 3/ EPC Class-1 HF
Supports MIFARE Classic encryption in read/write mode
Low-Power Card Detection
Compliance to “EMV contactless protocol specification V2.0.1” on RF level can be achieved
Antenna connection with minimum number of external components
Supported host interfaces:
- SPI up to 10 Mbit/s
- I²C-bus interfaces up to 400 kBd in Fast mode, up to 1000 kBd in Fast mode plus
- RS232 Serial UART up to 1228.8 kBd, with voltage levels dependent on pin voltage supply
Separate I²C-bus interface for connection of a secure access module (SAM)
FIFO buffer with size of 512 byte for highest transaction performance
Flexible and efficient power saving modes including hard power down, standby and low-power card detection
Cost saving by integrated PLL to derive system CPU clock from 27.12 MHz RF quartz crystal
3.3 V to 5 V power supply
Up to 8 free programmable input/output pins
Typical operating distance in read/write mode for communication to a ISO/IEC 14443A/MIFARE Card up to 12 cm, depending on the antenna size and tuning

产品实物图

封装

型号	订购码 (12NC)	可订购的器件编号	产品状态	封装
CLRC66301HN	9352 934 46557	CLRC66301HN,557	量产	HVQFN32 (SOT617-1)
CLRC66301HN	9352 934 46551	CLRC66301HN,551	量产	HVQFN32 (SOT617-1)

订货和供应

型号	订购码 (12NC)	可订购的器件编号	化学成分
CLRC66301HN	9352 934 46557	CLRC66301HN,557	CLRC66301HN
CLRC66301HN	9352 934 46551	CLRC66301HN,551	CLRC66301HN

CLRC66301HN 技术支持

档案名称	标题	类型	格式
CLRC66301HN	Contactless reader IC	Data sheet	pdf
AN11019	CLRC663, MFRC630, MFRC631, SLRC610 Antenna Design Guide	Application note	pdf
AN11022	CLRC663 Quickstart Guide	Application note	pdf
AN11021	CLRC663, MFRC631, MFRC630, SLRC610 Software Design Guide for NXPRDLib	Application note	pdf
AN11116	Using the RS232 serial evaluation boards on a USB port	Application note	pdf
AN11145	CLRC663, MFRC630, MFRC631, SLRC610 PC-Serial RS232 and low power card detection Quick Start Guide	Application note	pdf
AN11211	Quick Start Up Guide RC663 Blueboard	Application note	pdf
AN11256	Migration guide CLRC663 to derivates	Application note	pdf
AN11342	How to Scale Down the NXP Reader Library	Application note	pdf
939775017138	Next-generation multiprotocol contactless reader IC (CLRC663 only)	Leaflet	pdf
939775017290	The next generation of multiprotocol contactless proximity reader ICs	Leaflet	pdf
AN11246_239810	CLRC663, MFRC631, MFRC630, CLRC610 Directly Matched Antenna design - advanced user	Other type	zip
AN11020_206110	Matching Calculations CLRC663, MFRC631, MFRC630, SLRC610	Other type	zip
210910	CLRC663 redboard scripts	Software	zip
200312	NXP Reader Library version 2.1 with Visual C++ project	Software	zip
NXP_RFID_213911	Eagle parts library	Software	zip
UM10663	NXP Reader Library User Manual based on CLRC663 and PN512 Blueboard Reader projects	User manual	pdf
SOT617-1_115	HVQFN32; Reel pack; SMD, 7"; standard product orientation Orderable part number ending, 115 or X Ordering code (12NC) ending 115	Packing	pdf
SOT617-1_118	HVQFN32; Standard product orientation 12NC ending 118	Packing	pdf
sot617-1_fr	Footprint for reflow soldering SOT617-1	Reflow soldering	pdf
sot617-1_po	plastic thermal enhanced very thin quad flat package; no leads; 32 terminals; body 5 x 5 x 0.85 mm	Outline drawing	pdf