PCA9527DP 3-channel bidirectional bus extender for HDMI, I2C-bus and SMBus
The PCA9527 is a 3-channel bidirectional open-drain bus buffer for Display Data Control (DDC) clock, data and Consumer Electronic Control (CEC) for HDMI application. The device has two power supply pins to allow voltage level shift from 2.7 V to 5 V, and a rise time accelerator on port A of each DDC clock and data for driving longer cable (up to 18 meters or 1400 pF reliably without violating the bus rise time). The 5 V tolerant CEC channel is internally connected to VCC(B) and has no rise time accelerator. The CEC channel can be used as an interrupt or reset.
While retaining all the operating modes and features of the I²C-bus system during the level shift, it also permits extension of the I²C-bus by providing bidirectional buffering for data (SDA), clock (SCL), and CEC. Using the PCA9527 enables the system designer to isolate bus capacitance to meet HDMI DDC version 1.3 distance specification. The SDAx and SCLx pins are overvoltage tolerant and are high-impedance when the PCA9527 is unpowered. The port B drivers (SDAB, SCLB, CECB) with static level offset behave much like the drivers on the PCA9515 device, while the SDAA and SCLA drivers integrate the rise time accelerator, sink more current and eliminate the static offset voltage. The CECA driver has the same current and static offset voltage features as the SDAA and SCLA, but it does not have the rise time accelerator and is powered and referenced to VCC(B). This results in a LOW on the port B translating into a nearly 0 V LOW on port A, providing zero offset. The static level offset design of the port B I/O drivers prevent them from being connected to another device that has rise time accelerator including the PCA9507 (port B), PCA9510, PCA9511, PCA9512, PCA9513, PCA9514, PCA9515, PCA9516A, PCA9517 (port B), or PCA9518A. Port A of two or more PCA9527s can be connected together, however, to allow a star topography with port A on the common bus, and port A can be connected directly to any other buffer with static or dynamic offset voltage. Multiple PCA9527s can be connected in series, port A to port B, with no build-up in offset voltage with only time of flight delays to consider. Rise time accelerators on the SDAA and SCLA pins are turned on when input threshold is above 0.3VCC(A). The PCA9527 SDA and SCL drivers are not enabled unless VCC(A) and VCC(B) are above 2.7 V. The EN pin can also be used to turn the drivers on and off under system control. Caution should be observed to only change the state of the enable pin when the bus is idle. The output pull-down on the port B internal buffer LOW is set for approximately 0.5 V, while the input threshold of the internal buffer is set about 70 mV lower (0.43 V). When the port B I/O is driven LOW internally, the LOW is not recognized as a LOW by the input. This prevents a lock-up condition from occurring
产品特点 Features
- 3-channel, bidirectional buffer isolates capacitance allowing 1400 pF on port A and 400 pF on port B
- Exceeds 18 meters (above the maximum distance for HDMI DDC)
- Rise time accelerator and normal I/O on port A (no accelerator for CEC)
- Static level offset on port B
- Voltage level translation from 2.7 V to 5.5 V
- CEC is 5 V tolerant, powered by VCC(B)
- Upgrade replacement over PCA9507 and PCA9517A for cable application
- I²C-bus, SMBus and DDC-bus compatible
- Active HIGH buffer enable input
- Open-drain input/outputs
- Lock-up free operation
- Supports arbitration and clock stretching across the repeater
- Accommodates Standard-mode and Fast-mode I²C-bus devices and multiple masters
- Powered-off high-impedance I²C-bus pins
- Port A operating supply voltage range of 2.7 V to 5.5 V
- Port B operating supply voltage range of 2.7 V to 3.6 V
- 5 V tolerant I²C-bus and enable pins
- 0 Hz to 400 kHz clock frequency (the maximum system operating frequency may be less than 400 kHz because of the delays added by the repeater)
- ESD protection exceeds 8000 V HBM per JESD22-A114, 500 V MM per JESD22-A115, and 1000 V CDM per JESD22-C101
- Latch-up testing is done to JEDEC Standard JESD78 which exceeds 100 mA
- Package offered: TSSOP10
|
功能框图
|
封装
| 型号 |
可订购的器件编号 |
订购码 (12NC) |
产品状态 |
封装 |
| PCA9527DP |
9352 891 05118 |
PCA9527DP,118 |
量产 |
TSSOP10
(SOT552-1) |
订货和供应
| 型号 |
订购码 (12NC) |
可订购的器件编号 |
化学成分 |
| PCA9527DP |
9352 891 05118 |
PCA9527DP,118 |
PCA9527DP |
PCA9527DP 技术支持
| 档案名称 |
标题 |
类型 |
格式 |
| PCA9527DP |
3-channel bidirectional bus extender for HDMI, I2C-bus and SMBus |
Data sheet |
pdf |
| AN10441 |
Level shifting techniques in I2C-bus design
|
Application note |
pdf |
| AN255 |
I2C / SMBus Repeaters, Hubs and Expanders
|
Application note |
pdf |
| AN10710 |
Features and applications of the PCA9527 I2C-bus extender
|
Application note |
pdf |
| 75016527 |
Extend standard I2C-bus devices without worrying about offset voltages; NXP I2C-bus extender PCA9527 in a proven application
|
Brochure |
pdf |
| 75016532 |
Extend the I2C-bus with advanced repeaters and hubs; NXP 2-channel I2C-bus repeaters PCA9527x and 5-channel I2C-bus hubs PCA9516x
|
Leaflet |
pdf |
| 75016080 |
Extend the reach of any I2C-bus system without special offset voltage levels; NXP I2C-bus extender PCA9527
|
Leaflet |
pdf |
| 75017424 |
NXP I2C-bus solutions 2013: Smart, simple solutions for the 12 most common design concerns
|
Leaflet |
pdf |
| UM10204 |
I2C-bus specification and user manual
|
User manual |
pdf |
| UM10206 |
I2C Demonstration Board 2005-1 Quick Start Guide
|
User manual |
pdf |
| UM10323 |
PCA9600 demonstration board OM6293
|
User manual |
pdf |
