PN533 USB NFC Integrated Solution

The PN533 is a highly integrated transceiver module for contactless communication at 13.56 MHz based on the 80C51 microcontroller core. It supports 6 different operating modes:

ISO/IEC 14443A/MIFARE Reader/Writer
FeliCa Reader/Writer
ISO/IEC 14443B Reader/Writer
ISO/IEC 14443A/MIFARE Card MIFARE 1 KB or MIFARE 4 KB emulation
FeliCa Card emulation
ISO/IEC 18092, ECMA 340 Peer-to-Peer

The PN533 implements a demodulator and decoder for signals from ISO/IEC 14443A/MIFARE compatible cards and transponders. The PN533 handles the complete ISO/IEC 14443A framing and error detection (Parity & CRC).

The PN533 supports MIFARE 1 KB or MIFARE 4 KB emulation products. The PN533 supports contactless communication using MIFARE Higher transfer speeds up to 424 kbit/s in both directions.

The PN533 can demodulate and decode FeliCa coded signals. The PN533 handles the FeliCa framing and error detection. The PN533 supports contactless communication using FeliCa Higher transfer speeds up to 424 kbit/s in both directions.

The PN533 supports layers 2 and 3 of the ISO/IEC 14443 B Reader/Writer communication scheme, except anticollision. This must be implemented in firmware as well as upper layers.

In card emulation mode, the PN533 is able to answer to a Reader/Writer command either according to the FeliCa or ISO/IEC 14443A/MIFARE card interface scheme. The PN533 generates the load modulation signals, either from its transmitter or from the LOADMOD pin driving an external active circuit. A complete secure card functionality is only possible in combination with a secure IC using the NFC-WI/S²C interface.

Compliant to ECMA 340 and ISO/IEC 18092 NFCIP-1 Passive and Active communication modes, the PN533 offers the possibility to communicate to another NFCIP-1 compliant device, at transfer speeds up to 424 kbit/s.The PN533 handles the complete NFCIP-1 framing and error detection.

The PN533 transceiver can be connected to an external antenna for Reader/Writer or Card/PICC modes, without any additional active component.

The PN533 supports the following host interfaces:

USB 2.0 full speed interface (bus powered or non bus powered)
High Speed UART (HSU)

PN533 has also a master I²C interface enabling the drive on an I²C peripheral (i.e. memory).

In addition, a power switch is included to supply power to a secure IC

产品特点 Features

80C51 microcontroller core with 45056 bytes ROM and 1224 bytes RAM
Highly integrated demodulator and decoder
Buffered output drivers to connect an antenna with minimum number of external components
Integrated RF level detector
Integrated data mode detector
Supports ISO/IEC 14443A/MIFARE
Supports ISO/IEC 14443B (Reader/Writer mode only)
Typical operating distance in Reader/Writer mode for communication to ISO/IEC 14443A/MIFARE, ISO/IEC 14443B or FeliCa cards up to 50 mm depending on antenna size and tuning
Typical operating distance in NFCIP-1 mode up to 50 mm depending on antenna size, tuning and power supply
Typical operating distance in ISO/IEC 14443A/MIFARE or FeliCa card emulation mode of approximately 100 mm depending on antenna size, tuning and external field strength
Supports MIFARE 1 KB or MIFARE 4 KB emulation encryption in Reader/Writer mode and MIFARE higher transfer speed communication at 212 kbit/s and 424 kbit/s
Supports contactless communication according to the FeliCa protocol at 212 kbit/s and 424 kbit/s
Integrated RF interface for NFCIP-1 up to 424 kbit/s
Possibility to communicate on the RF interface above 424 kbit/s using external analog components
Supported host interfaces
- USB 2.0 full speed interface
- High-speed UART
Restricted I²C master interface to control an external I²C EEPROM
Dedicated host interrupts
Low power modes
- Hard-Power-down mode
- Soft-Power-down mode
Automatic wake-up on HSU interfaces when device is in Power-down mode
Programmable timers
27.12 MHz Crystal oscillator
On-Chip PLL to generate internally The 96 MHz for the USB interface
Power modes
- USB bus power mode
- 2.5 V to 3.6 V power supply operating range in non USB bus power mode
Power switch for external secure companion chip
Dedicated IO ports for external device control
Integrated antenna detector for production tests
ECMA 373 NFC-WI interface to connect an external secure IC

应用

Computing application
Consumer applications

产品实物图

封装

型号	订购码 (12NC)	可订购的器件编号	产品状态	封装
PN5331B3HN/C270	9352 878 68518	PN5331B3HN/C270,51	量产	HVQFN40 (SOT618-1)
PN5331B3HN/C270	9352 878 68557	PN5331B3HN/C270:55	量产	HVQFN40 (SOT618-1)
PN5331B3HN/C270	9352 878 68551	PN5331B3HN/C270,55	量产	HVQFN40 (SOT618-1)

订货和供应

型号	订购码 (12NC)	可订购的器件编号	化学成分
PN5331B3HN/C270	9352 878 68518	PN5331B3HN/C270,51	PN5331B3HN/C270
PN5331B3HN/C270	9352 878 68557	PN5331B3HN/C270:55	PN5331B3HN/C270
PN5331B3HN/C270	9352 878 68551	PN5331B3HN/C270,55	PN5331B3HN/C270

PN533 技术支持

档案名称	标题	类型	格式
PN533	Transmission module	Data sheet	pdf
AN98080	Read/write devices based on the HITAG read/write IC HTRC110	Application note	pdf
200312	NXP Reader Library version 2.1 with Visual C++ project	Software	zip
NXP_RFID_213911	Eagle parts library	Software	zip