UJA1069TW LIN fail-safe system basis chip
The UJA1069 fail-safe System Basis Chip (SBC) replaces basic discrete components which are common in every Electronic Control Unit (ECU) with a Local Interconnect Network (LIN) interface. The fail-safe SBC supports all networking applications which control various power and sensor peripherals by using LIN as a local sub-bus. The fail-safe SBC contains the following integrated devices:
- LIN transceiver compliant with LIN 2.0 and SAE J2602, and compatible with LIN 1.3
- Advanced independent watchdog
- Dedicated voltage regulator for microcontroller
- Serial peripheral interface (full duplex)
- Local wake-up input port
- Inhibit/limp-home output port
In addition to the advantages of integrating these common ECU functions in a single package, the fail-safe SBC offers an intelligent combination of system-specific functions such as:
- Advanced low-power concept
- Safe and controlled system start-up behavior
- Advanced fail-safe system behavior that prevents any conceivable deadlock
- Detailed status reporting on system and sub-system levels
The UJA1069 is designed to be used in combination with a microcontroller and a LIN controller. The fail-safe SBC ensures that the microcontroller is always started up in a defined manner. In failure situations the fail-safe SBC will maintain the microcontroller function for as long as possible, to provide full monitoring and software driven fall-back operation.
The UJA1069 is designed for 14 V single power supply architectures and for 14 V and 42 V dual power supply architectures
产品特点 Features
General
- Contains a full set of LIN ECU functions:
- LIN transceiver
- Voltage regulator for the microcontroller (5.0 V)
- Enhanced window watchdog with on-chip oscillator
- Serial Peripheral Interface (SPI) for the microcontroller
- ECU power management system
- Fully integrated autonomous fail-safe system
- Designed for automotive applications:
- Supports 14 V and 42 V architectures
- Excellent ElectroMagnetic Compatibility (EMC) performance
- +-8 kV ElectroStatic Discharge (ESD) protection Human Body Model (HBM) for off-board pins
- +-4 kV ElectroStatic Discharge (ESD) protection IEC 61000-4-2 for off-board pins
- +-60 V short-circuit proof LIN-bus pin
- Battery and LIN-bus pins are protected against transients in accordance with ISO 7637-3
- Very low sleep current
- Supports remote flash programming via the LIN-bus
- Available in:
- Small 6.4 mm x 7.8 mm HTSSOP24 package with low thermal resistance
- Small 8 mm x 11 mm HTSSOP32 package with low thermal resistance
LIN transceiver
- LIN 2.0 and SAE J2602 compliant LIN transceiver
- Enhanced error signalling and reporting
- Downward compatible with LIN 1.3 and the TJA1020
Power management
- Smart operating modes and power management modes
- Cyclic wake-up capability in Standby and Sleep mode
- Local wake-up input with cyclic supply feature
- Remote wake-up capability via the LIN-bus
- External voltage regulators can easily be incorporated in the power supply system (flexible and fail-safe)
- 42 V battery related high-side switch for driving external loads such as relays and wake-up switches
- Intelligent maskable interrupt output
Fail-safe features
- Safe and predictable behavior under all conditions
- Programmable fail-safe coded window and time-out watchdog with on-chip oscillator, guaranteeing autonomous fail-safe system supervision
- Fail-safe coded 16-bit SPI interface for the microcontroller
- Global enable pin for the control of safety-critical hardware
- Detection and detailed reporting of failures:
- On-chip oscillator failure and watchdog alerts
- Battery and voltage regulator undervoltages
- LIN-bus failures (short-circuits)
- TXDL and RXDL clamping situations and short-circuits
- Clamped or open reset line
- SPI message errors
- Overtemperature warning
- Rigorous error handling based on diagnostics
- Supply failure early warning allows critical data to be stored
- 23 bits of access-protected RAM is available e.g. for logging of cyclic problems
- Reporting in a single SPI message; no assembly of multiple SPI frames needed
- Limp-home output signal for activating application hardware in case system enters Fail-safe mode (e.g. for switching on warning lights)
- Fail-safe coded activation of Software development mode and Flash mode
- Unique SPI readable device type identification
- Software-initiated system reset
封装
| 型号 |
订购码 (12NC) |
可订购的器件编号 |
产品状态 |
封装 |
| UJA1069TW/5V0/C/T |
9352 888 72518 |
UJA1069TW/5V0/C/T |
量产 |
HTSSOP32
(SOT549-1) |
| UJA1069TW/5V0/C/T |
9352 888 72512 |
UJA1069TW/5V0/C/T, |
量产 |
HTSSOP32
(SOT549-1) |
订货和供应
| 型号 |
订购码 (12NC) |
可订购的器件编号 |
化学成分 |
| UJA1069TW/5V0/C/T |
9352 888 72518 |
UJA1069TW/5V0/C/T |
UJA1069TW/5V0/C/T |
| UJA1069TW/5V0/C/T |
9352 888 72512 |
UJA1069TW/5V0/C/T, |
UJA1069TW/5V0/C/T |
UJA1069TW 技术支持
| 档案名称 |
标题 |
类型 |
格式 |
| UJA1069TW |
LIN fail-safe system basis chip |
Data sheet |
pdf |
| AN10853 |
ESD and EMC sensitivity of IC
|
Application note |
pdf |
| UM10301 |
User Manual for NXP Real Time Clocks PCF85x3, PCA8565 and PCF2123, PCA2125
|
User manual |
pdf |
| UM10569 |
Store and transport requirements
|
User manual |
pdf |
| R_10015 |
Chip-On-Glass (COG) - a cost-effective and reliable technology for LCD displays
|
Other type |
pdf |
| UM10204 |
I2C-bus specification and user manual
|
User manual |
pdf |
| UM10206 |
I2C Demonstration Board 2005-1 Quick Start Guide
|
User manual |
pdf |
| UM10569 |
Store and transport requirements
|
User manual |
pdf |
| UM10204_JA |
I2C-bus specification and user manual
|
User manual |
pdf |
