AD7934: 内置序列器的4通道、1.5 MSPS、12位并行ADC

AD7933/AD7934分别是10位和12位高速、低功耗、逐次逼近型(SAR)模数转换器(ADC),采用2.7 V至5.25 V单电源供电,最高吞吐量达1.5 MSPS。这些器件均内置一个低噪声、宽带宽、差分采样保持放大器,可处理最高达50 MHz的输入频率。AD7933/AD7934具有4个带通道序列器的模拟输入通道,可以通过预先编程选择通道转换顺序。这些器件可接受单端、全差分或伪差分模拟输入。转换过程和数据采集过程均通过标准控制输入进行控制,使器件与微处理器和DSP可实现轻松接口。输入信号在CONVST的下降沿进行采样,而转换同时在此处启动。AD7933/AD7934内置一个精确的2.5 V片内基准电压源,可用作模数转换的基准电压源。或者,可将外部基准电压加载至此引脚,为其提供基准电压。这些器件采用先进的设计技术,可在高吞吐量的情况下实现极低的功耗,还提供灵活的功耗管理选项。利用一个片内控制寄存器,用户可以设置不同的工作条件,包括模拟输入范围和配置、输出编码、功耗管理及通道序列化。

The AD7933/AD7934 are 10-bit and 12-bit, high speed, low power, successive approximation (SAR) analog-to-digital converters (ADCs). The parts operate from a single 2.7 V to 5.25 V power supply and feature throughput rates up to 1.5 MSPS. The parts contain a low noise, wide bandwidth, differential track-and-hold amplifier that handles input frequencies up to 50 MHz.

The AD7933/AD7934 feature four analog input channels with a channel sequencer that allows a preprogrammed selection of channels to be sequentially converted. These parts can accept either single-ended, fully differential, or pseudo differential analog inputs.The conversion process and data acquisition are controlled using standard control inputs that allow for easy interfacing to microprocessors and DSPs. The input signal is sampled on the falling edge of CONVST, and the conversion is also initiated at this point.The AD7933/AD7934 has an accurate on-chip 2.5 V reference that is used as the reference source for the analog-to-digital conversion. Alternatively, this pin can be overdriven to provide an external reference.These parts use advanced design techniques to achieve very low power dissipation at high throughput rates. They also feature flexible power management options. An on-chip control register allows the user to set up different operating conditions, including analog input range and configuration, output coding, power management, and channel sequencing.

AD7934 特点
AD7934 技术指标
AD7934 亮点
  1. 高吞吐量、低功耗。
  2. 4个带通道序列器的模拟输入。
  3. 精确的2.5 V片内基准电压源。
  4. 单端、伪差分或全差分模拟输入,可通过软件选择。
  5. 利用V DRIVE功能实现单电源供电。利用V DRIVE功能,并行接口可直接连至独立于V DD的3 V或5 V处理器系统。
  6. 无流水线延迟。
  7. 通过CONVST输入与一次性转换控制可实现对采样时间的精确控制。
AD7934 建议配套产品
AD7934 功能框图

AD7934 产品选型
产品型号 产品状态 封装 Pins 报价*
(1000 pcs.)
AD7934BRU Prodn 28 ld TSSOP (4.4mm) 28 $ 7.81
AD7934BRU-REEL Prodn 28 ld TSSOP (4.4mm) 28 $ 7.81
AD7934BRU-REEL7 Prodn 28 ld TSSOP (4.4mm) 28 $ 7.81
AD7934BRUZ Prodn 28 ld TSSOP (4.4mm) 28 $ 7.10
AD7934BRUZ-REEL7 Prodn 28 ld TSSOP (4.4mm) 28 $ 7.10
EVAL-AD7934CB Prodn EVALUATION BOARDS - $ 150.00
AD7934 应用技术支持与电子电路设计开发资源下载
  1. AD7934 数据手册DataSheet下载 . pdf
  2. Analog Devices, Inc.ADI 美国模拟器件公司产品订购手册 .pdf
  3. ADC模数转换器选型指南 . pdf