ATMEL智能卡读卡器产品AT83C24

AT83C24 概述

The AT83C24 is a smart card reader interface IC for smart card reader/writer applications such as EFT/POS terminals and set top boxes. It enables the management of any type of smart card from any kind of host. Up to 8 AT83C24 can be connected in parallel using the programmable TWI address.
Its high efficiency DC/DC converter, low quiescent current in standby mode makes it particularly suited to low power and portable applications. The reduced bill of material allows reducing significantly the system cost. A sophisticated protection system guarantees timely and controlled shutdown upon error conditions.
The AT83C24NDS is a dedicated version approved by NDS for use with NDS VideoGuard conditional access software in set-top boxes. All AT83C24 datasheet is applicable to AT83C24NDS. The main differences between AT83C24 and AT83C24NDS are listed below: 1/CLASS A card supplied with CVCC = 4.75 to 5.25V for AT83C24NDS, CLASS A card supplied with CVCC = 4.6 to 5.25V for AT83C24
2/18MHz minimum on input clock for AT83C24NDS
3/Up to 10μF for capacitor connected on CVCC pin for AT83C24,
3.3μF mandatory for AT83C24NDS

AT83C24 特性

• Smart Card Interface
  –Compliance with ISO 7816, EMV2000, GIE-CB, GSM and WHQL Standards
  Card Clock Stop High or Low for Card Power-down Modes
  Support Synchronous Cards with C4 and C8 Contacts
  Card Detection and Automatic de-activation Sequence
  Programmable Activation Sequence
  –Direct Connection to the Smart Card
  Logic Level Shifters
  Short Circuit Current Limitation (see electrical characteristics)
  8kV+ ESD Protection (MIL/STD 883 Class 3)
  –Programmable Voltage
  5V ±5% at 65 mA (Class A)
  3V ±0.2V at 65 mA (Class B)
  1.8V ±0.14V at 40 mA
  –Low Ripple Noise: < 200 mV
  •Versatile Host Interface
  –ICAM (Conditional Access) Compatible
  –Two Wire Interface (TWI) Link
  Programmable Address Allow up to 8 Devices
  –Programmable Interrupt Output
  –Automatic Level Shifter (1.6V to VCC)
  •Reset Output Includes
  –Power-On Reset (POR)
  –Power-Fail Detector (PFD)
  •High-efficiency Step-up Converter: 80 to 98% Efficiency
  •Extended Voltage Operation: 3V to 5.5V
  •Low Power Consumption
  –180 mA Maximum In-rush Current
  –30 μA Typical Power-down Current (without Smart Card)
  •4 to 48 MHz Clock Input, 7 MHz Min for Step-up Converter (for AT83C24)
  •18 to 48MHz Clock input (for AT83C24NDS)
  •Industrial Temperature Range: -40 to +85°C
  •Packages: SO28 and QFN28

AT83C24 订购型号

Part Number	Supply Voltage	Package	Temperature Range	Packing
AT83C24B-PRTUL	3V to 5.5V	PLCC28	Industrial Green	Tray
AT83C24B-PRRUL	3V to 5.5V	PLCC28	Industrial Green	Tape Reel
AT83C24B-PRTUM	4.00V to 5.5V	VQFP32	Industrial Green	Tray
AT83C24B-PRRUM	4.00V to 5.5V	VQFP32	Industrial Green	Tape Reel
AT83C24B-TISUL	3V to 5.5V	SO28	Industrial Green	Stick
AT83C24B-TIRUL	3V to 5.5V	SO28	Industrial Green	Tape Reel
AT83C24B-TISUM	4.00V to 5.5V	SO28	Industrial Green	Stick
AT83C24B-TIRUM	4.00V to 5.5V	SO28	Industrial Green	Tape Reel
AT83C24NDS-PRTUL	3V to 5.5V	QFN28	Industrial Green	Tray
AT83C24NDS-PRRUL	3V to 5.5V	QFN28	Industrial Green	Tape Reel
AT83C24NDS-PRTUM	4.00V to 5.5V	QFN28	Industrial Green	Tray
AT83C24NDS-PRRUM	4.00V to 5.5V	QFN28	Industrial Green	Tape Reel