TLE9262QX V33
The TLE9262QXV33 is a monolithic integrated circuit in an exposed pad VQFN-48 (7mm x 7mm) power package with Lead Tip Inspection (LTI) feature to support Automatic Optical Inspection (AOI). The device is designed for various CAN-LIN automotive applications as main supply for the microcontroller and as interface for a LIN and CAN bus network.
To support these applications, the System Basis Chip (SBC) provides the main functions, such as a 3.3V lowdropout voltage regulator (LDO) for e.g. a microcontroller supply, another 5V low-dropout voltage regulator with off-board protection for e.g. sensor supply, another 3.3V/1.8V regulator to drive an external PNP transistor, which can be used as an independent supply for off-board usage or in load sharing configuration with the main regulator VCC1, a HS-CAN transceiver supporting CAN FD and LIN transceiver for data transmission, high-side switches with embedded protective functions and a 16-bit Serial Peripheral Interface (SPI) to control and monitor the device. Also implemented are a configurable timeout / window watchdog circuit with a reset feature, three Fail Outputs and an under voltage reset feature.
The device offers low-power modes in order to minimize current consumption on applications that are connected permanently to the battery. A wake-up from the low-power mode is possible via a message on the buses, via the bi-level sensitive monitoring/wake-up inputs as well as via cyclic wake.
The device is designed to withstand the severe conditions of automotive applications.
| Parametric | TLE9262QX V33 |
|---|
| Transceiver | 1 x LIN2.2 / J2602 |
|---|
| Transceiver | High Speed CAN ISO 11898 - 5 |
|---|
| Transmission Rate
max | 2.0MBit/s |
|---|
| Voltage Regulator Output | 3.3V / 250 mA |
|---|
| Voltage Regulator Output | 3.3V or 1.8V / 400 mA |
|---|
| Voltage Regulator Output | 5V / 100 mA |
|---|
| Output Drivers | 4 x High-Side Switch 150 mA |
|---|
| Failure Management | 3 x Limp-Home Outputs |
|---|
| Failure Management | CAN Failure Detection |
|---|
| Failure Management | Fail-Safe |
|---|
| Quiescent Current | 15 μA (typ) Sleep Mode (5V off) |
|---|
| Standby Current | 44 μA (typ) Stop Mode (5V on) |
|---|
| Wake-up Inputs | Wake Pins, CAN, LIN |
|---|
| Family | Mid-Range SBC |
|---|
| Sales Product Name | TLE9262QX V33 |
|---|
| OPN | TLE9262QXV33XUMA1 |
|---|
| Product Status | active and preferred |
|---|
| Package Name | PG-VQFN-48 |
|---|
| Completely lead free | yes |
|---|
| Halogen free | yes |
|---|
| RoHS compliant | yes |
|---|
| Packing Size | 2500 |
|---|
| Packing Type | TAPE & REEL |
|---|
| Moisture Level | 3 |
|---|
| Summary of Features:- Very low quiescent current consumption in Stop- and Sleep Mode
- Periodic Cyclic Wake in SBC Normal- and Stop Mode
- Periodic Cyclic Sense in SBC Normal-, Stop- and Sleep Mode
- Low-Drop Voltage Regulator 3.3V, 250mA
- Low-Drop Voltage Regulator 5V, 100mA, protected features for off-board usage
- Low-Drop Voltage Regulator, driving an external PNP transistor - 3.3V in load sharing configuration or 3.3V/1.8V in stand-alone configuration, protected features for off-board usage. Current limitation by shunt resistor (up to 350mA with 470mΩ external shunt resistor) in stand-alone configuration
- High-Speed CAN Transceiver
- LIN Transceiver LIN 2.2, J2602 with configurable TXD timeout feature and LIN Flash Mode
- Fully compliant to “Hardware Requirements for LIN, CAN and FlexRay Interfaces in Automotive Applications”
- Four High-Side Outputs 7Ω typ.
- Dedicated supply pin for High-Side Outputs
- Two General Purpose High-Voltage In- and Outputs (GPIOs) configurable as add. Fail Outputs, Wake Inputs, Low-Side switches or High-Side switches
- Three universal High-Voltage Wake Inputs for voltage level monitoring
- Alternate High-Voltage Measurement Function, e.g. for battery voltage sensing
- Configurable wake-up sources
- Reset Output
- Configurable timeout and window watchdog
- Up to three Fail Outputs (depending on configuration)
- Over temperature and short circuit protection feature
- Wide supply input voltage and temperature range
- Software compatible to all SBC families TLE926x and TLE927x
- Green Product (RoHS compliant) & AEC Qualified
- PG-VQFN-48 leadless exposed-pad power package with Lead Tip Inspection (LTI) feature to support Automatic Optical Inspection (AOI)
 |
Data Sheet
Product Selection Guide
Evaluation Boards
| Board | Family | Description | Status |
|---|
| DEMOBOARD TLE9263QX | System Basis Chip (SBC) | MId-Range SBC Evaluation Board enables the device evaluation and accelerates the design-in phase. The Evaluation Board can be connected to the “XC2000 power easy kit” and controlled, via USB, using a powerful and intuitive Graphical User Interface (GUI) installed on your computer. TLE9263-3QXV33TLE9260-3QXTLE9260-3QXV33TLE9260QXTLE9260QXV33TLE9261-3QXTLE9261-3QXV33TLE9261QXTLE9261QXV33TLE9262-3QXTLE9262-3QXV33TLE9262QXTLE9262QXV33TLE9263-3QXTLE9263QXTLE9263QXV33 | on request |
Package Data
