ADG5209F Fault Protection, −0.4 pC QINJ, 4:1 Dual Multiplexer

The source pins are protected against voltages greater than the supply rails, up to −55 V and +55 V. The source pins are protected against voltages between −55 V and +55 V in an unpowered state. Trench isolation guards against latch-up. Optimized for low charge injection and on capacitance. The ADG5208F/ADG5209F can be operated from a dual supply of ±5 V up to ±22 V or a single power supply of 8 V up to 44 V.

The ADG5208F and ADG5209F are 8:1 and dual 4:1 analog multiplexers. The ADG5208F switches one of eight inputs to a common output, and the ADG5209F switches one of four differential inputs to a common differential output. An EN input on both devices enables or disables the device. Each channel conducts equally well in both directions when on, and each channel has an input signal range that extends to the supplies. The digital inputs are compatible with 3 V logic inputs over the full operating supply range.

When no power supplies are present, the channelremains in the off condition, and the switch inputs are high impedance. Under normal operating conditions, if the analog input signal levels on any Sx pin exceed positive fault voltage (VDD) or negative fault voltage (VSS) by a threshold voltage (VT), the channel turns off and that Sx pin becomes high impedance. If the fault channel is selected, the drain pin is pulled to the secondary supply voltage that was exceeded.

Input signal levels of up to −55 V or +55 V relative to ground are blocked, in both the powered and unpowered conditions.

The low capacitance and charge injection of these switches make them ideal solutions for data acquisition and sample-and-hold applications, where low glitch switching and fast settling times are required.

Product Highlights

Applications

Features and Benefits
  • Overvoltage protection up to −55 V and +55 V
  • Power-off protection up to −55 V and +55 V
  • Overvoltage detection on source pins
  • Low charge injection (QINJ): −0.4 pC
  • Low on capacitance: 14 pF
  • Latch-up immune under any circumstance
  • Known state without digital inputs present
  • VSS to VDD analog signal range
  • ±5 V to ±22 V dual-supply operation
  • 8 V to 44 V single-supply operation
  • Fully specified at ±15 V, ±20 V, +12 V, and +36 V
  • Switches & Multiplexers
    IBIS Models
    Data Sheets
    Documentnote
    ADG5208F/ADG5209F: Fault Protection, −0.4 pC QINJ, 8:1/Dual 4:1 Multiplexers (Rev. A)PDF 548.58 K
    User Guides
    Documentnote
    UG-875: Evaluating the ADG5209F, Overvoltage Protected Dual 4:1 Multiplexer (Rev. A)PDF 371.33 K
    Order Information
    Part NumberPackagePacking QtyTemp RangePrice 100-499Price 1000+RoHS
    ADG5209FBCPZ-RL7 Production16 ld LFCSP 4x4 REEL 150040 to 125C04.21Y
    ADG5209FBRUZ Production16 ld TSSOPOTH 96-40 to 125C5.144.21Y
    ADG5209FBRUZ-RL7 Production16 ld TSSOPREEL 1000-40 to 125C04.21Y
    Evaluation Boards
    Part NumberDescriptionPriceRoHS
    EVAL-ADG5209FEBZEvaluation Board60Y
    ADG5208F/ADG5209F:故障保护、 −0.4 pC Q INJ 、 8:1/ 双通道 4:1 多路复用器 (Rev. A) adg5208f
    ADG5208F/ADG5209F: Fault Protection, −0.4 pC QINJ, 8:1/Dual 4:1 Multiplexers (Rev. A) adg5208f
    ADG5209F TSSOP IBIS Model (Rev. 1.0) adg5209f
    UG-875: Evaluating the ADG5209F, Overvoltage Protected Dual 4:1 Multiplexer (Rev. A) adg5209f