TLE4998C4

The linear Hall IC TLE4998C has been designed specifically to meet the requirements of highly accurate angle and position detection as well as for current measurement applications. The sensor provides a digital SPC (Short PWM Code) signal, based on the standardized SENT (Single Edge Nibble Transmission, SAE J2716) protocol. The SPC protocol allows transmissions initiated by the ECU. Two further operation modes are available: “range selection” for dynamical switching of the measurement range during operation ,“ID selection” to build a bus system with up to 4 ICs on a single output line and a common supply, which can be individually accessed by the ECU. Each transmission sequence contains an adjustable number of nibbles representing the magnetic field, the temperature value and a status information of the sensor.The output stage is an open-drain driver pulling the output pin to low only. Therefore, the high level needs to be obtained by an external pull-up resistor. This output type has the advantage that the receiver may use an even lower supply voltage (e.g. 3.3 V). In this case the pull-up resistor must be connected to the given receiver supply. The IC is produced in BiCMOS technology with high voltage capability, and it also has reverse-polarity protection. Digital signal processing using a 16-bit DSP architecture together with digital temperature compensation guarantee excellent long-time stability compared to analog compensation methods. While the overall resolution is 16 bits, some internal stages work with resolutions up to 20 bits.

ParametricTLE4998C4
ApplicationsLinear Hall
PackageLeaded
Programmableyes
InterfacesSPC
Sales Product NameTLE4998C4
OPNTLE4998C4HALA1
Product Statusactive and preferred
Package NamePG-SSO-4
Completely lead freeyes
Halogen freeno
RoHS compliantyes
Packing Size2000
Packing TypeAMMO-PACK
Summary of Features:
  • SPC (Short PWM Code) protocol with enhanced interface features based on SENT (Single Edge Nibble Transmission,defined by SAE J2716)
  • 20-bit Digital Signal Processing (DSP)
  • Digital temperature compensation
  • 16-bit overall resolution
  • Operates within automotive temperature range
  • Low drift of output signal over temperature and lifetime
  • Programmable parameters stored in EEPROM with single-bit error correction: SPC protocol modes: synchronous transmission, dynamic range selection, ID selection mode,SPC unit time,Magnetic range and sensitivity (gain), polarity of the output slope,Offset,Bandwidth,Clamping levels,Customer temperature compensation coefficients,Memory lock Re-programmable until memory lock
  • Supply voltage 4.5 - 5.5 V (4.1 - 16 V in extended range)
  • Operation between -200 mT and +200 mT within three ranges
  • Reverse-polarity and overvoltage protection for all pins
  • Output short-circuit protection
  • On-board diagnostics (overvoltage, EEPROM error, start up)
  • Output of internal magnetic field values and temperature
  • Programming and operation of multiple sensors with common power supply
  • Two-point calibration of magnetic transfer function without iteration steps
  • High immunity against mechanical stress, EMC, ESD
Target Applications:
  • Robust replacement of potentiometers,No mechanical abrasion,Resistant to humidity, temperature, pollution and vibration
  • Linear and angular position sensing in automotive applications such as pedal position, suspension control, throttle position, headlight levelling, and steering torque sensing
  • Sensing of high current for battery management, motor control,and electronic fuses
Data Sheet
TitleSizeDateVersion
TLE4998C4_Data_Sheet_Rev1.0,EN1.8 MB15 Jan 201001_00
Application Notes
TitleSizeDateVersion
TLE499x - Application Note Throttle Position Sensing1 MB01 Jul 200801_00
Pedal Position Sensing Using Hall Effect Sensors3.3 MB10 Sep 200901_00
Electric Power Steering (EPS) with GMR-Based Angular and Linear Hall Sensor1.2 MB23 Oct 200801_00
Current Sensing940 KB23 Feb 200901_01
TLE4998 - Temperature Compensation Setup Guide769 KB30 Oct 200801_01
TLE4998 - 2 Point Calibration Setup Guide429 KB01 Aug 200801_00
TLE4998C - Programming Guide SPC (Preliminary Version)837 KB01 Feb 200901_00
Product Brief
TitleSizeDateVersion
TLE4998x118 KB01 Jan 2008
Application Brochure
TitleSizeDateVersion
Solutions for Wind Energy Systems5.4 MB01 Apr 201301_00
Transportation Brochure (24-60V)6.9 MB01 Jul 2013
Product Selection Guide
TitleSizeDateVersion
Industrial Automation 20135.1 MB01 Jan 201301_00
Sensor Solutions for Automotive, Industrial and Consumer Applications 2016EN5.7 MB28 Apr 201601_01
Material Content SheetInfo
TitleSizeDateVersion
MCDS_2013-08-28_22-44-55_MA000863088_PG-SSO-4-1.pdf19 KB31 Oct 201301_00
PCB Design Data
TitleSizeDateVersion
PCB Footprints&Symbols - Linear Hall ICs - Altium128 KB30 Sep 201302_00
PCB Footprints&Symbols - Linear Hall ICs - Cadence114 KB30 Sep 201302_00
PCB Footprints&Symbols - Linear Hall ICs - Eagle78 KB30 Sep 201302_00
PCB Footprints&Symbols - Linear Hall ICs - Mentor122 KB30 Sep 201302_00
Evaluation Boards
BoardFamilyDescriptionStatus
EVAL ISO1I813TGate DriverISOFACE™ ISO1I813T Evaluation Board for galvanically isolated 8-Channel Digital Input Ics with IEC61131-2 compatible characteristics for industrial applicationsISO1I813Tactive and preferred
TLE4998 EVALBOARDSensorAn evaluation board which allows evaluation of the linear Hall TLE4998 family.TLE 4998xon request
TLE4998X PROGRAMMER KITSensorThe kit consists of a PGSISI box (programming interface) and an evaluation board which allows evaluation of the linear Hall TLE 4998 family. The evaluation board (PCB) is available seperately (without PGSISI box). See TLE4998 EVALBOARD.TLE 4998xactive and preferred
PGSISI-2 INTERFACE BOXon request
Package Data
TitleSizeDateVersion
PG-SSO-4-1 | TLE4998C4HALA1EN405 KB11 Apr 201601_00
PCB Design Data
TitleSizeDateVersion
PCB Footprints&Symbols - Linear Hall ICs - Altium128 KB30 Sep 201302_00
PCB Footprints&Symbols - Linear Hall ICs - Cadence114 KB30 Sep 201302_00
PCB Footprints&Symbols - Linear Hall ICs - Eagle78 KB30 Sep 201302_00
PCB Footprints&Symbols - Linear Hall ICs - Mentor122 KB30 Sep 201302_00
EN TLE4998C4
Current Sensing TLE4998C4
TLE4998 - 2 Point Calibration Setup Guide TLE4998C4
Electric Power Steering (EPS) with GMR-Based Angular and Linear Hall Sensor TLE4998C4
TLE499x - Application Note Throttle Position Sensing TLE4998C4
TLE4998 - Temperature Compensation Setup Guide TLE4998C4
Pedal Position Sensing Using Hall Effect Sensors TLE4998C4
TLE4998C - Programming Guide SPC (Preliminary Version) TLE4998C4
TLE4998x TLE4998C4
Solutions for Wind Energy Systems TLE4954CB+E2
Transportation Brochure (24-60V) KP229E3518
Industrial Automation 2013 TLE4998C4
EN SP370-23-156-0
MCDS_2013-08-28_22-44-55_MA000863088_PG-SSO-4-1.pdf TLE4998C4
EN TLE4998C4
PCB Footprints&Symbols - Linear Hall ICs - Altium TLE4998C4
PCB Footprints&Symbols - Linear Hall ICs - Cadence TLE4998C4
PCB Footprints&Symbols - Linear Hall ICs - Eagle TLE4998C4
PCB Footprints&Symbols - Linear Hall ICs - Mentor TLE4998C4