TLE4998P3C infineon _ BDTIC a Leading Distributor in China

TLE4998P3C

The linear Hall IC TLE4998P3C has been designed specifically to meet the requirements of highly accurate rotation and position detection, as well as for current measurement applications. Two capacitors are integrated on the lead frame, making this sensor especially suitable for demanding EMC requirements .The sensor provides a digital PWM signal, which is ideally suited for direct decoding by any unit measuring a duty cycle of a rectangular signal (usually a timer/capture unit in a microcontroller). The output stage is an open-drain driver pulling the output pad to low only. Therefore, the high level must be obtained by an external pull-up resistor. This output type has the advantage that the receiver may use even a lower supply voltage (e.g. 3.3 V). In this case, the pull-up resistor must be connected to the given receiver supply.The IC is produced in BiCMOS technology with high voltage capability, also providing reverse polarity protection. Digital signal processing, using a 16-bit DSP architecture together with digital temperature compensation, guarantees excellent long-time stability as compared to analog compensation methods. While the overall resolution is 16 bits, some internal stages work with resolutions up to 20 bits. The PWM output frequency can be selected within the range of 122 Hz up to 1953 Hz.

Parametric	TLE4998P3C
Applications	Linear Hall
Package	Leaded
Programmable	yes
Interfaces	PWM

Sales Product Name	TLE4998P3C
OPN	TLE4998P3CHAMA1
Product Status	active and preferred
Package Name	PG-SSO-3
Completely lead free	yes
Halogen free	no
RoHS compliant	yes
Packing Size	1500
Packing Type	AMMO-PACK

Summary of Features:

SPC (Short PWM Code) protocol with enhanced interface features based on SENT (Single Edge Nibble Transmission,defined by SAE J2716)
20-bit Digital Signal Processing (DSP)
Digital temperature compensation
16-bit overall resolution
Operates within automotive temperature range
Low drift of output signal over temperature and lifetime
Programmable parameters stored in EEPROM with single-bit error correction: SPC protocol modes: synchronous transmission, dynamic range selection, ID selection mode,SPC unit time,Magnetic range and sensitivity (gain), polarity of the output slope,Offset,Bandwidth,Clamping levels,Customer temperature compensation coefficients,Memory lock Re-programmable until memory lock
Supply voltage 4.5 - 5.5 V (4.1 - 16 V in extended range)
Operation between -200 mT and +200 mT within three ranges
Reverse-polarity and overvoltage protection for all pins
Output short-circuit protection
On-board diagnostics (overvoltage, EEPROM error, start up)
Output of internal magnetic field values and temperature
Programming and operation of multiple sensors with common power supply
Two-point calibration of magnetic transfer function without iteration steps
High immunity against mechanical stress, EMC, ESD
Package with two capacitors:47nF(VDD to GND) and 4.7nF(OUT to GND)

Target Applications:

Robust replacement of potentiometers,No mechanical abrasion,Resistant to humidity, temperature, pollution and vibration
Linear and angular position sensing in automotive applications such as pedal position, suspension control, throttle position, headlight levelling, and steering torque sensing
Sensing of high current for battery management, motor control,and electronic fuses

Data Sheet

Title	Size	Date	Version
TLE4998P3C,EN	1.4 MB	01 Sep 2009	01_01

Application Notes

Title	Size	Date	Version
Pedal Position Sensing Using Hall Effect Sensors	3.3 MB	10 Sep 2009	01_00
Measuring Liquid Levels Using Hall Effect Sensors	349 KB	10 Sep 2009	01_00
Current Sensing	940 KB	23 Feb 2009	01_01
Electric Power Steering (EPS) with GMR-Based Angular and Linear Hall Sensor	1.2 MB	23 Oct 2008	01_00
TLE499x - Application Note Throttle Position Sensing	1 MB	01 Jul 2008	01_00
TLE4998 - 2 Point Calibration Setup Guide	429 KB	01 Aug 2008	01_00

Application Brief

Title	Size	Date	Version
Infineon-ISO 26262 Safety Brief - Infineon Magnetic Position Sensors-AB-v01_00-EN；EN	329 KB	11 Jun 2015	01_00

Application Brochure

Title	Size	Date	Version
Solutions for Wind Energy Systems	5.4 MB	01 Apr 2013	01_00
Transportation Brochure (24-60V)	6.9 MB	01 Jul 2013

Product Selection Guide

Title	Size	Date	Version
Sensor Solutions for Automotive, Industrial and Consumer Applications 2016；EN	5.7 MB	28 Apr 2016	01_01
Industrial Automation 2013	5.1 MB	01 Jan 2013	01_00

Material Content SheetInfo

Title	Size	Date	Version
MCDS_2013-08-28_22-22-03_MA000876788_PG-SSO-3-92.pdf	20 KB	31 Oct 2013	01_00

Evaluation Boards

Board	Family	Description	Status
EVAL ISO1I813T	Gate Driver	ISOFACE™ ISO1I813T Evaluation Board for galvanically isolated 8-Channel Digital Input Ics with IEC61131-2 compatible characteristics for industrial applicationsISO1I813T	active and preferred
TLE4998 EVALBOARD	Sensor	An evaluation board which allows evaluation of the linear Hall TLE4998 family.TLE 4998x	on request
TLE4998X PROGRAMMER KIT	Sensor	The kit consists of a PGSISI box (programming interface) and an evaluation board which allows evaluation of the linear Hall TLE 4998 family. The evaluation board (PCB) is available seperately (without PGSISI box). See TLE4998 EVALBOARD.TLE 4998x	active and preferred
PGSISI-2 INTERFACE BOX			on request