TLE9262-3QX

The TLE9262-3QX is a monolithic integrated circuit in an exposed pad VQFN-48 (7mm x 7mm) power package with Lead Tip Inspection (LTI) feature to support Automatic Optical Inspection (AOI). The device is designed for various CAN- LIN automotive applications as main supply for the microcontroller and as interface for a LIN and CAN bus network including the CAN Partial Networking feature. To support these applications, the S ystem Basis Chip (SBC) provides the main functions, such as a 5V low-dropout voltage regulator (LDO) for e.g. a microcontroller supply, another 5V low-dropout voltage regulator with off-board protection for e.g. sensor supply, another 5V/3.3V regulator to drive an external PNP transistor, which can be used as an independent supply for off-board usage or in load sharing configuration with the main regulator VCC1, a HS-CAN transceiver supporting CAN FD and CAN Partial Networking (incl. FD tolerant mode) and LIN transceiver for data transmission, high-side switches with embedded protective functions and a 16-bit Serial Peripheral Interface (SPI) to control and monitor the device. Also implemented are a configurable timeout / window watchdog circuit with a reset feature, three Fail Outputs and an under voltage reset feature. The device offers low-power modes in order to minimize current consumption on applications that are connected permanently to the battery. A wake-up from the low-power mode is possible via a message on the buses, via the bi-level sensitive monitoring/wake-up inputs as well as via cyclic wake. The device is designed to withstand the severe conditions of automotive applications.

ParametricTLE9262-3QX
Transceiver1 x LIN2.2 / J2602
TransceiverHigh Speed CAN ISO 11898 - 6
Transmission Rate  max2.0MBit/s
Voltage Regulator Output5V / 250 mA
Voltage Regulator Output5V / 100 mA
Voltage Regulator Output5V or 3.3V / 400 mA
Output Drivers4 x High-Side Switch 150 mA
Failure Management3 x Limp-Home Outputs
Failure ManagementCAN Failure Detection
Failure ManagementFail-Safe Mode
Quiescent Current15 μA (typ) Sleep Mode (5V off)
Standby Current44 μA (typ) Stop Mode (5V on)
Wake-up InputsWake Pins, CAN, LIN
FamilyMid-Range SBC
Sales Product NameTLE9262-3QX
OPNTLE92623QXXUMA2
Product Statusactive and preferred
Package NamePG-VQFN-48
Completely lead freeyes
Halogen freeyes
RoHS compliantyes
Packing Size2500
Packing TypeTAPE & REEL
Moisture Level3
Summary of Features:
  • Very low quiescent current consumption in Stop- and Sleep Mode
  • Periodic Cyclic Wake in SBC Normal- and Stop Mode
  • Periodic Cyclic Sense in SBC Normal-, Stop- and Sleep Mode
  • Low-Drop Voltage Regulator 5V, 250mA
  • Low-Drop Voltage Regulator 5V, 100mA, protected features for off-board usage
  • Low-Drop Voltage Regulator, driving an external PNP transistor - 5V in load sharing configuration or 5V/3.3V in stand-alone configuration, protected features for off-board usage. Current limitation by shunt resistor (up to 350mA with 470mΩ external shunt resistor) in stand-alone configuration
  • High-Speed CAN Transceiver: fully compliant to ISO11898-2 and ISO11898-5 fully compliant to ISO11898-6 (Partial Networking) inclunding CAN FD tolerant feature suitable for chokeless operation up to 500kbps supporting CAN FD communication up to 2 Mbps
  • fully compliant to ISO11898-2 and ISO11898-5
  • fully compliant to ISO11898-6 (Partial Networking) inclunding CAN FD tolerant feature
  • suitable for chokeless operation up to 500kbps
  • supporting CAN FD communication up to 2 Mbps
  • LIN Transceiver LIN 2.2, J2602 with configurable TXD timeout feature and LIN Flash Mode
  • Fully compliant to “Hardware Requirements for LIN, CAN and FlexRay Interfaces in Automotive Applications” Revision 1.3, 2012-05-04
  • Four High-Side Outputs 7Ω typ.
  • Dedicated supply pin for High-Side Outputs
  • Two General Purpose High-Voltage In- and Outputs (GPIOs) configurable as add. Fail Outputs, Wake Inputs, Low-Side switches or High-Side switches
  • Three universal High-Voltage Wake Inputs for voltage level monitoring
  • Alternate High-Voltage Measurement Function, e.g. for battery voltage sensing
  • Configurable wake-up sources
  • Reset Output
  • Configurable timeout and window watchdog
  • Up to three Fail Outputs (depending on configuration)
  • Over temperature and short circuit protection feature
  • Wide supply input voltage and temperature range
  • Software compatible to all
  • SBC families TLE926x and TLE927x
  • Green Product (RoHS compliant) & AEC Qualified
  • PG-VQFN-48 leadless exposed-pad power package with Lead Tip Inspection (LTI) feature to support Automatic Optical Inspection (AOI)
Target Applications:
  • Body control modules
  • Gateway
  • Climate control
  • Seat control
  • Door control and closures
  • Light control modules
  • Engine management systems
Data Sheet
TitleSizeDateVersion
TLE9262-3QX Data Sheet,EN7.1 MB28 Oct 201401_00
TLE9262QX Data Sheet6.1 MB01 Oct 201401_01
Product Brief
TitleSizeDateVersion
TLE926x-3QX Product Brief181 KB30 Apr 2014
FAQ Document
TitleSizeDateVersion
Mid-Range SBC FAQ420 KB01 Oct 201401_01
Product Selection Guide
TitleSizeDateVersion
Automotive Power Selection GuideEN10.6 MB19 Jan 201601_01
PCB Design Data
TitleSizeDateVersion
PCB Footprints and Symbols - TLE9262-3QX - Mid-Range SBC Family - Mentor - v1.0.zipEN5 KB27 Jul 201501_00
PCB Footprints and Symbols - TLE9262-3QX - Mid-Range SBC Family - Cadence - v1.0.zipEN19 KB27 Jul 201501_00
PCB Footprints and Symbols - TLE9262-3QX - Mid-Range SBC Family - Altium - v1.0.zipEN707 KB27 Jul 201501_00
PCB Footprints and Symbols - TLE9262-3QX - Mid-Range SBC Family - Eagle - v1.0.zipEN3 KB29 Jul 201501_00
Evaluation Boards
BoardFamilyDescriptionStatus
DEMOBOARD TLE9263QXSystem Basis Chip (SBC)MId-Range SBC Evaluation Board enables the device evaluation and accelerates the design-in phase. The Evaluation Board can be connected to the “XC2000 power easy kit” and controlled, via USB, using a powerful and intuitive Graphical User Interface (GUI) installed on your computer. TLE9263-3QXV33TLE9260-3QXTLE9260-3QXV33TLE9260QXTLE9260QXV33TLE9261-3QXTLE9261-3QXV33TLE9261QXTLE9261QXV33TLE9262-3QXTLE9262-3QXV33TLE9262QXTLE9262QXV33TLE9263-3QXTLE9263QXTLE9263QXV33on request
Package Data
TitleSizeDateVersion
PG-VQFN-48-31 | TLE92623QXXUMA2EN742 KB11 Apr 201601_00
PCB Design Data
TitleSizeDateVersion
PCB Footprints and Symbols - TLE9262-3QX - Mid-Range SBC Family - Mentor - v1.0.zipEN5 KB27 Jul 201501_00
PCB Footprints and Symbols - TLE9262-3QX - Mid-Range SBC Family - Cadence - v1.0.zipEN19 KB27 Jul 201501_00
PCB Footprints and Symbols - TLE9262-3QX - Mid-Range SBC Family - Altium - v1.0.zipEN707 KB27 Jul 201501_00
PCB Footprints and Symbols - TLE9262-3QX - Mid-Range SBC Family - Eagle - v1.0.zipEN3 KB29 Jul 201501_00
EN TLE9262-3QX
TLE9262QX Data Sheet TLE9262-3QX
TLE926x-3QX Product Brief TLE9263-3QX
Mid-Range SBC FAQ TLE9263-3QX
EN TLE8203E
EN TLE9262-3QX
EN TLE9262-3QX
EN TLE9262-3QX
EN TLE9262-3QX
EN TLE9262-3QX