LPC2119FBD64: Single-chip 16/32-bit microcontrollers; 64/128/256 kB ISP/IAP flash with 10-bit ADC and CAN
The LPC2109/2119/2129 are based on a 16/32-bit ARM7TDMI-S CPU with real-time emulation and embedded trace support, together with 64/128/256 kB of embedded high-speed flash memory. A 128-bit wide memory interface and a unique accelerator architecture enable 32-bit code execution at maximum clock rate. For critical code size applications, the alternative 16-bit Thumb mode reduces code by more than 30 % with minimal performance penalty.
With their compact 64-pin package, low power consumption, various 32-bit timers, 4-channel 10-bit ADC, two advanced CAN channels, PWM channels and 46 fast GPIO lines with up to nine external interrupt pins these microcontrollers are particularly suitable for automotive and industrial control applications, as well as medical systems and fault-tolerant maintenance buses. With a wide range of additional serial communications interfaces, they are also suited for communication gateways and protocol converters as well as many other general-purpose applications.
Remark: Throughout the data sheet, the term LPC2109/2119/2129 will apply to devices with and without the /00 or /01 suffixes. The /00 or the /01 suffix will be used to differentiate from other devices only when necessary.
LPC2119FBD64: Product Block Diagram
Outline 3d SOT314-2
2.1 Key features brought by LPC2109/2119/2129/01 devices
- Fast GPIO ports enable port pin toggling up to 3.5 times faster than the original device. They also allow for a port pin to be read at any time regardless of its function.
- Dedicated result registers for ADC(s) reduce interrupt overhead. The ADC pads are 5 V tolerant when configured for digital I/O function(s).
- UART0/1 include fractional baud rate generator, auto-bauding capabilities and handshake flow-control fully implemented in hardware.
- Buffered SSP serial controller supporting SPI, 4-wire SSI, and Microwire formats.
- SPI programmable data length and master mode enhancement.
- Diversified Code Read Protection (CRP) enables different security levels to be implemented. This feature is available in LPC2109/2119/2129/00 devices as well.
- General purpose timers can operate as external event counters.
2.2 Key features common for all devices
- 16/32-bit ARM7TDMI-S microcontroller in a tiny LQFP64 package.
- 8/16 kB on-chip SRAM.
- 64/128/256 kB on-chip flash program memory. 128-bit wide interface/accelerator enables high speed 60 MHz operation.
- In-System Programming (ISP) and In-Application Programming (IAP) via on-chip bootloader software. Flash programming takes 1 ms per 512 B line. Single sector or full chip erase takes 400 ms.
- EmbeddedICE-RT interface enables breakpoints and watch points. Interrupt service routines can continue to execute while the foreground task is debugged with the on-chip RealMonitor software.
- Embedded Trace Macrocell (ETM) enables non-intrusive high speed real-time tracing of instruction execution.
- Two interconnected CAN interfaces (one for LPC2109) with advanced acceptance filters.
- Four-channel 10-bit A/D converter with conversion time as low as 2.44 µs.
- Multiple serial interfaces including two UARTs (16C550), Fast I²C-bus (400 kbit/s) and two SPIs.
- 60 MHz maximum CPU clock available from programmable on-chip Phase-Locked Loop with settling time of 100 µs.
- Vectored Interrupt Controller with configurable priorities and vector addresses.
- Two 32-bit timers (with four capture and four compare channels), PWM unit (six outputs), Real-Time Clock (RTC) and watchdog.
- Up to forty-six 5 V tolerant general purpose I/O pins. Up to nine edge or level sensitive external interrupt pins available.
- On-chip crystal oscillator with an operating range of 1 MHz to 30 MHz.
- Two low power modes, Idle and Power-down.
- Processor wake-up from Power-down mode via external interrupt.
- Individual enable/disable of peripheral functions for power optimization.
- Dual power supply:
CPU operating voltage range of 1.65 V to 1.95 V (1.8 V ± 0.15 V).
I/O power supply range of 3.0 V to 3.6 V (3.3 V ± 10 %) with 5 V tolerant I/O pads.
Data Sheets (1)
Errata (2)
Application Notes (15)
Users Guides (1)
Brochures (1)
Package Information (1)
Supporting Information (8)
Software
Ordering Information
| Product | Status | Core | Clock speed [max] (MHz) | Flash (kB) | DMIPS | RAM (kB) | EEPROM (kB) | GPIO | Ethernet | USB | USB (speed) | USB (type) | LCD | CAN | UART | I²C | SPI | I²S | ADC channels | ADC (bits) | DAC (bits) | SCTimer / PWM | Timers | Timer (bits) | RTC | PWM | Package name | IOH | Temperature range | Supply voltage [min] (V) | Supply voltage [max] (V) | Product category | Demoboard |
|---|
| LPC2119FBD64/01 | Active | ARM7 | 60 | 128 | | 16 | | 46 | | | | | | 2 | 2 | 1 | 2 | | 4 | 10 | | | 3 | 32 | 1 | 6 | LQFP64 | | -40 °C to +85 °C | 1.65 | 1.95 | | |
| LPC2119FBD64 | No Longer Manufactured | ARM7 | 60 | 128 | | 16 | | 46 | | | | | | 2 | 2 | 1 | 2 | | 4 | 10 | | 1 | 3 | 32 | 1 | 6 | LQFP64 | N | -40 °C to +85 °C | 1.65 | 1.95 | 150-LPC2100/200/300/400- | |
| LPC2119FBD64/00 | No Longer Manufactured | ARM7 | 60 | 128 | | 16 | | 46 | | | | | | 2 | 2 | 1 | 2 | | 4 | 10 | | | 3 | 32 | 1 | 6 | LQFP64 | | -40 °C to +85 °C | 1.65 | 1.95 | | |
Package Information
| Product ID | Package Description | Outline Version | Reflow/Wave Soldering | Packing | Product Status | Part NumberOrdering code(12NC) | Marking | Chemical Content | RoHS / Pb Free / RHF | LeadFree Conversion Date | EFR | IFR(FIT) | MTBF(hour) | MSL | MSL LF |
|---|
| LPC2119FBD64/00 | | SOT314-2 | HTQFP-HLQFP-LQFP-MSQFP-WAVE | Tray, Bakeable, Single | Withdrawn | LPC2119FBD64/00,15
(9352 823 52151) | Standard Marking | |    | Always Pb-free | 0.0 | 2.84 | 2.58E8 | 1 | 1 |
| LPC2119FBD64/01 | | SOT314-2 | HTQFP-HLQFP-LQFP-MSQFP-WAVE | Tray, Bakeable, Single | Active | LPC2119FBD64/01,15
(9352 848 86151) | Standard Marking | LPC2119FBD64/01 | | Always Pb-free | 0.0 | 2.84 | 2.58E8 | 1 | 1 |
