PCA9624: 8-bit Fm+ I²C-bus 100 mA 40 V LED driver
The PCA9624 is an I²C-bus controlled 8-bit LED driver optimized for voltage switch
dimming and blinking 100 mA Red/Green/Blue/Amber (RGBA) LEDs. Each LED output
has its own 8-bit resolution (256 steps) fixed frequency individual PWM controller that
operates at 97 kHz with a duty cycle that is adjustable from 0 % to 99.6 % to allow the
LED to be set to a specific brightness value. An additional 8-bit resolution (256 steps)
group PWM controller has both a fixed frequency of 190 Hz and an adjustable frequency
between 24 Hz to once every 10.73 seconds with a duty cycle that is adjustable from 0 %
to 99.6 % that is used to either dim or blink all LEDs with the same value.
Each LED output can be off, on (no PWM control), set at its individual PWM controller
value or at both individual and group PWM controller values. The PCA9624 operates with
a supply voltage range of 2.3 V to 5.5 V and the 100 mA open-drain outputs allow
voltages up to 40 V.
The PCA9624 is one of the first LED controller devices in a new Fast-mode Plus (Fm+)
family. Fm+ devices offer higher frequency (up to 1 MHz) and more densely populated
bus operation (up to 4000 pF).
The active LOW Output Enable input pin (OE) blinks all the LED outputs and can be used
to externally PWM the outputs, which is useful when multiple devices must be dimmed or
blinked together without using software control.
Software programmable LED group and three Sub Call I²C-bus addresses allow all or
defined groups of PCA9624 devices to respond to a common I²C-bus address, allowing
for example, all red LEDs to be turned on or off at the same time or marquee chasing
effect, thus minimizing I²C-bus commands. Seven hardware address pins allow up to
126 devices on the same bus.
The Software Reset (SWRST) Call allows the master to perform a reset of the PCA9624
through the I²C-bus, identical to the Power-On Reset (POR) that initializes the registers to
their default state causing the outputs to be set HIGH (LED off). This allows an easy and
quick way to reconfigure all device registers to the same condition.
The PCA9624 and PCA9634 software is identical and if the PCA9624 on-chip 100 mA
NAND FETs do not provide enough current or voltage to drive the LEDs, then the
PCA9634 with larger current or higher voltage external drivers can be used.
PCA9624: Product Block Diagram
sot616-3_3d
Data Sheets (1)
Users Guides (3)
Brochures (2)
Package Information (2)
Packing (2)
Supporting Information (1)
Ordering Information
| Product | Status | Package version |
|---|
| PCA9624BS | Active | SOT616-3 |
| PCA9624PW | Active | SOT355-1 |
Package Information
| Product ID | Package Description | Outline Version | Reflow/Wave Soldering | Packing | Product Status | Part NumberOrdering code(12NC) | Marking | Chemical Content | RoHS / Pb Free / RHF | LeadFree Conversion Date | EFR | IFR(FIT) | MTBF(hour) | MSL | MSL LF |
|---|
| PCA9624PW |  | SOT355-1 | SSOP-TSSOP-VSO-WAVE | Reel 13" Q1/T1 | Active | PCA9624PW,118
(9352 863 03118) | PCA9624PW | PCA9624PW |    | Always Pb-free | 0.0 | 5.0 | 2E8 | 1 | 1 |
| Bulk Pack | Active | PCA9624PW,112
(9352 863 03112) | PCA9624PW | PCA9624PW | | Always Pb-free | 0.0 | 5.0 | 2E8 | 1 | 1 |
| PCA9624BS | | SOT616-3 | | Reel 13" Q1/T1 | Active | PCA9624BS,118
(9352 863 02118) | 9624 | PCA9624BS | | Always Pb-free | 0.0 | 5.0 | 2E8 | 1 | 1 |
