• 简体中文
• English

PCT2075: I²C-bus Fm+, 1 degree C accuracy, digital temperature sensor and thermal watchdog

The PCT2075 is a temperature-to-digital converter featuring ±1 °C accuracy over ‑25 °C to +100 °C range. It uses an on-chip band gap temperature sensor and Sigma-Delta A‑to‑D conversion technique with an overtemperature detection output that is a drop-in replacement for other LM75 series thermal sensors. The device contains a number of data registers: Configuration register (Conf) to store the device settings such as device operation mode, OS operation mode, OS polarity and OS fault queue; temperature register (Temp) to store the digital temp reading, set-point registers (Tos and Thyst) to store programmable overtemperature shutdown and hysteresis limits, and programmable temperature sensor sampling time Tidle, that can be communicated by a controller via the 2-wire serial I²C-bus Fast-mode Plus interface.

The PCT2075 also includes an open-drain output (OS) which becomes active when the temperature exceeds the programmed limits. The OS output operates in either of two selectable modes: OS comparator mode or OS interrupt mode. Its active state can be selected as either HIGH or LOW. The fault queue that defines the number of consecutive faults in order to activate the OS output is programmable as well as the set-point limits.

The PCT2075 can be configured for different operation conditions. It can be set in normal mode to periodically monitor the ambient temperature, or in shut-down mode to minimize power consumption.

The temperature register always stores an 11-bit two’s complement data, giving a temperature resolution of 0.125 °C. This high temperature resolution is particularly useful in applications of measuring precisely the thermal drift or runaway. When the device is accessed the conversion in process is not interrupted (that is, the I²C-bus section is totally independent of the Sigma-Delta converter section) and accessing the device continuously without waiting at least one conversion time between communications will not prevent the device from updating the Temp register with a new conversion result. The new conversion result will be available immediately after the Temp register is updated. It is also possible to read just one of the temperature register bytes without lock-up.

The PCT2075 powers up in the normal operation mode with the OS in comparator mode, temperature threshold of 80 °C and hysteresis of 75 °C, so that it can be used as a stand-alone thermostat with those pre-defined temperature set points. The default set points can be modified during manufacture and ordered under custom part number.

There are three selectable logic address pins with three logic states so that 27 8-pin devices or three 6-pin devices can be connected on the same bus without address conflict.

sot1069-2_3d

Data Sheets (1)

Selector Guides (1)

Package Information (4)

Packing (3)

Supporting Information (4)

Ordering Information

Package Information

Product ID	Package Description	Outline Version	Reflow/Wave Soldering	Packing	Product Status	Part NumberOrdering code(12NC)	Marking	Chemical Content	RoHS / Pb Free / RHF	LeadFree Conversion Date	EFR	IFR(FIT)	MTBF(hour)	MSL	MSL LF
PCT2075D		SOT96-1	SO-SOJ-REFLOW SO-SOJ-WAVE SO-SOJ-REFLOW SO-SOJ-WAVE	Reel 13" Q1/T1	Active	PCT2075D,118 (9352 968 98118)	Standard Marking	PCT2075D		Always Pb-free	0.0	4.0	2.5E8	1	1
PCT2075TP		SOT1069-2		Reel 7" Q2/T3	Active	PCT2075TP,147 (9352 969 01147)	Standard Marking	PCT2075TP		Always Pb-free	0.0	4.0	2.5E8	1	1
PCT2075DP		SOT505-1	Reflow_Soldering_Profile	Reel 13" Q1/T1	Active	PCT2075DP,118 (9352 968 99118)	Standard Marking	PCT2075DP		Always Pb-free	0.0	4.0	2.5E8	1	1
PCT2075GV		SOT1353-1		Reel 7" Q1/T1	Active	PCT2075GVX (9353 002 78115)	Standard Marking	PCT2075GV		Always Pb-free				1	1
				Reel 13" Q1/T1	Active	PCT2075GVJ (9353 002 78118)	Standard Marking	PCT2075GV		Always Pb-free				1	1