UJA1075ATW: High-speed CAN/ LIN core system basis chip
The UJA1075A core System Basis Chip (SBC) replaces the basic discrete components commonly found in Electronic Control Units (ECU) with a high-speed Controller Area Network (CAN) and a Local Interconnect Network (LIN) interface.
The UJA1075A supports the networking applications used to control power and sensor peripherals by using a high-speed CAN as the main network interface and the LIN interface as a local sub-bus.
The core SBC contains the following integrated devices:
In addition to the advantages gained from integrating these common ECU functions in a single package, the core SBC offers an intelligent combination of system-specific functions such as:
The UJA1075A is designed to be used in combination with a microcontroller that incorporates a CAN controller. The SBC ensures that the microcontroller always starts up in a controlled manner.
sot549-1_3d
2.1 General
- Contains a full set of CAN and LIN ECU functions: CAN transceiver and LIN transceiver Scalable 3.3 V or 5 V voltage regulator delivering up to 250 mA for a microcontroller and peripheral circuitry; an external PNP transistor can be connected for better heat distribution over the PCB Separate voltage regulator for the CAN transceiver (5 V) Watchdog with Window and Timeout modes and on-chip oscillator Serial Peripheral Interface (SPI) for communicating with the microcontroller ECU power management system
- Designed for automotive applications: Enhanced ElectroMagnetic Compatibility (EMC) performance ±8 kV ElectroStatic Discharge (ESD) protection Human Body Model (HBM) on the CAN/LIN bus pins and the wake-up pins ±6 kV ElectroStatic Discharge protection IEC 61000-4-2 on the CAN/LIN bus pins and the wake-up pins ±58 V short-circuit proof CAN/LIN bus pins Battery and CAN/LIN bus pins are protected against transients in accordance with ISO 7637-3
- Supports remote flash programming via the CAN bus
- Small 6.1 mm × 11 mm HTSSOP32 package with low thermal resistance
- Pb-free; Restriction of Hazardous Substances Directive (RoHS) and dark green compliant
2.2 CAN transceiver
- ISO 11898-2 and ISO 11898-5 compliant high-speed CAN transceiver
- Dedicated low dropout voltage regulator for the CAN bus: Independent of the microcontroller supply Significantly improves EMC performance
- Bus connections are truly floating when power is off
- SPLIT output pin for stabilizing the recessive bus level
2.3 LIN transceiver
- LIN 2.1 compliant LIN transceiver
- Compliant with SAE J2602
- Downward compatible with LIN 2.0 and LIN 1.3
- Low slope mode for optimized EMC performance
- Integrated LIN termination diode at pin DLIN
2.4 Power management
- Wake-up via CAN, LIN or local wake-up pins with wake-up source detection
- 2 wake-up pins: WAKE1 and WAKE2 inputs can be switched off to reduce current flow Output signal (WBIAS) to bias the wake-up pins, selectable sampling time of 16 ms or 64 ms
- Standby mode with very low standby current and full wake-up capability; V1 active to maintain supply to the microcontroller
- Sleep mode with very low sleep current and full wake-up capability
2.5 Control and diagnostic features
- Safe and predictable behavior under all conditions
- Programmable watchdog with independent clock source: Window, Timeout (with optional cyclic wake-up) and Off modes supported (with automatic re-enable in the event of an interrupt)
- 16-bit Serial Peripheral Interface (SPI) for configuration, control and diagnosis
- Global enable output for controlling safety-critical hardware
- Limp home output (LIMP) for activating application-specific ‘limp home’ hardware in the event of a serious system malfunction
- Overtemperature shutdown
- Interrupt output pin; interrupts can be individually configured to signal V1/V2 undervoltage, CAN/LIN/local wake-up and cyclic and power-on interrupt events
- Bidirectional reset pin with variable power-on reset length to support a variety of microcontrollers
- Software-initiated system reset
2.6 Voltage regulators
- Main voltage regulator V1: Scalable voltage regulator for the microcontroller, its peripherals and additional external transceivers ±2 % accuracy 3.3 V and 5 V versions available Delivers up to 250 mA and can be combined with an external PNP transistor for better heat distribution over the PCB Selectable current threshold at which the external PNP transistor starts to deliver current Undervoltage warning at 90 % of nominal output voltage and undervoltage reset at 90 % or 70 % of nominal output voltage Can operate at VBAT voltages down to 4.5 V (e.g. during cranking), in accordance with ISO 7637 pulse 4/4b and ISO 16750-2 Stable output under all conditions
- Voltage regulator V2 for CAN transceiver: Dedicated voltage regulator for on-chip high-speed CAN transceiver Undervoltage warning at 90 % of nominal output voltage Can be switched off; CAN transceiver can be supplied by V1 or by an external voltage regulator Can operate at VBAT voltages down to 5.5 V (e.g. during cranking) in accordance with ISO 7637, pulse 4 Stable output under all conditions
Data Sheets (1)
| Name/Description | Modified Date |
|---|---|
| High-speed CAN/ LIN core system basis chip (REV 2.0) PDF (379.0 kB) UJA1075A | 28 Jan 2011 |
Package Information (1)
| Name/Description | Modified Date |
|---|---|
| plastic thermal enhanced thin shrink small outline package; 32 leads; body width 6.1 mm; lead pitch 0.65 mm; exposed die... (REV 1.0) PDF (380.0 kB) SOT549-1 | 08 Feb 2016 |
Ordering Information
| Product | Status | Product category | Category | Supported standards | Package name | Low power modes | Supply voltage [min] (V) | Package version | Supply voltage [max] (V) | Data rate [min] (kb/s) | Data rate [max] (kb/s) | CAN channels | LIN channels | Voltage on bus pins [min] (V) | Voltage on bus pins [max] (V) | VESD IEC61000-4-2 (kV) | FlexRay Channels | VESD HBM on bus pins (+/- kV) | VIO option available | Application | Recommended Version | Tvj [max] (°C) | Rth(j-a) (K/W) | SPLIT pin | Under-voltage detection | TX Dominant Time out | Over-temperature detection | INH / Wake Pin | Min High Input Levels (V) | No of pins |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| UJA1075ATW/5V0/WD | Active | SBC; High-Speed CAN; LIN Transceiver | ISO-11898-2; ISO-11898-5; LIN-2.1; SAE-J2602 | HTSSOP32 | Standby Mode; Sleep Mode | 4.5 | 40 | 15 | 1000 | 1 | 1 | -58 | 58 | 6 | 8 | No | Yes | 250mA | ||||||||||||
| UJA1075ATW/3V3/WD/1 | Active | SBC; High-Speed CAN; LIN Transceiver | ISO-11898-2; ISO-11898-5; LIN-2.1; SAE-J2602 | HTSSOP32 | Standby Mode; Sleep Mode | 4.5 | 40 | 15 | 1000 | 1 | 1 | -58 | 58 | 6 | 8 | No | Yes | 250mA | ||||||||||||
| UJA1075ATW/3V3/WD | Active | SBC; High-Speed CAN; LIN Transceiver | ISO-11898-2; ISO-11898-5; LIN-2.1; SAE-J2602 | HTSSOP32 | Standby Mode; Sleep Mode | 4.5 | 40 | 15 | 1000 | 1 | 1 | -58 | 58 | 6 | 8 | No | Yes | 250mA | ||||||||||||
| UJA1075ATW/3V3 | Active | SBC; High-Speed CAN; LIN Transceiver | ISO-11898-2; ISO-11898-5; LIN-2.1; SAE-J2602 | HTSSOP32 | Standby Mode; Sleep Mode | 4.5 | 40 | 15 | 1000 | 1 | 1 | -58 | 58 | 6 | 8 | No | Yes | 250mA | ||||||||||||
| UJA1075ATW/5V0/WD/1 | Active | SBC; High-Speed CAN; LIN Transceiver | ISO-11898-2; ISO-11898-5; LIN-2.1; SAE-J2602 | HTSSOP32 | Standby Mode; Sleep Mode | 4.5 | 40 | 15 | 1000 | 1 | 1 | -58 | 58 | 6 | 8 | No | Yes | 250mA | ||||||||||||
| UJA1075ATW/3V3/1 | Active | SBC; High-Speed CAN; LIN Transceiver | ISO-11898-2; ISO-11898-5; LIN-2.1; SAE-J2602 | HTSSOP32 | Standby Mode; Sleep Mode | 4.5 | 40 | 15 | 1000 | 1 | 1 | -58 | 58 | 6 | 8 | No | Yes | 250mA | ||||||||||||
| UJA1075ATW/5V0/1 | Active | SBC; High-Speed CAN; LIN Transceiver | ISO-11898-2; ISO-11898-5; LIN-2.1; SAE-J2602 | HTSSOP32 | Standby Mode; Sleep Mode | 4.5 | 40 | 15 | 1000 | 1 | 1 | -58 | 58 | 6 | 8 | No | Yes | 250mA | ||||||||||||
| UJA1075ATW/5V0 | Active | SBC; High-Speed CAN; LIN Transceiver | ISO-11898-2; ISO-11898-5; LIN-2.1; SAE-J2602 | HTSSOP32 | Standby Mode; Sleep Mode | 4.5 | 40 | 15 | 1000 | 1 | 1 | -58 | 58 | 6 | 8 | No | Yes | 250mA |
Package Information
| Product ID | Package Description | Outline Version | Reflow/Wave Soldering | Packing | Product Status | Part NumberOrdering code(12NC) | Marking | Chemical Content | RoHS / Pb Free / RHF | LeadFree Conversion Date | MSL | MSL LF |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| UJA1075ATW/3V3 | | SOT549-1 | Reel 13" Q1/T1 | Active | UJA1075ATW/3V3,118 (9352 924 18118) | Standard Marking | UJA1075ATW/3V3 |    | Always Pb-free | 1 | 1 | |
| UJA1075ATW/3V3/1 | | SOT549-1 | Reel 13" Q1/T1 | Active | UJA1075ATW/3V3/1J (9353 064 01118) | Standard Marking | UJA1075ATW/3V3/1 | | Always Pb-free | 1 | 1 | |
| UJA1075ATW/3V3/WD | | SOT549-1 | Reel 13" Q1/T1 | Active | UJA1075ATW/3V3WD,1 (9352 924 17118) | Standard Marking | UJA1075ATW/3V3/WD | | Always Pb-free | 1 | 1 | |
| UJA1075ATW/3V3/WD/1 | | SOT549-1 | Reel 13" Q1/T1 | Active | UJA1075ATW/3V3/WDJ (9353 063 99118) | Standard Marking | UJA1075ATW/3V3/WD/1 | | Always Pb-free | 1 | 1 | |
| UJA1075ATW/5V0 | | SOT549-1 | Reel 13" Q1/T1 | Active | UJA1075ATW/5V0,118 (9352 924 15118) | Standard Marking | UJA1075ATW/5V0 | | Always Pb-free | 1 | 1 | |
| UJA1075ATW/5V0/1 | | SOT549-1 | Reel 13" Q1/T1 | Active | UJA1075ATW/5V0/1J (9353 063 94118) | Standard Marking | UJA1075ATW/5V0/1 | | Always Pb-free | 1 | 1 | |
| UJA1075ATW/5V0/WD | | SOT549-1 | Reel 13" Q1/T1 | Active | UJA1075ATW/5V0WD,1 (9352 924 16118) | Standard Marking | UJA1075ATW/5V0/WD | | Always Pb-free | 1 | 1 | |
| UJA1075ATW/5V0/WD/1 | | SOT549-1 | Reel 13" Q1/T1 | Active | UJA1075ATW/5V0/WDJ (9353 063 98118) | Standard Marking | UJA1075ATW/5V0/WD/1 | | Always Pb-free | 1 | 1 |
- High-speed CAN/ LIN core system basis chip uja1075atw
