STEVAL-IFP028V1:Single high side driver based on IPS160H

The STEVAL-IFP028V1 is an evaluation board designed to analyze all IPS160H functionality.

It is designed to meet application requirements in terms of galvanic isolation between the user interface and the power interface. This requirement is satisfied via optical isolation implemented through two optocouplers, OPTO1 and OPT2, for forward signals to the device and for diagnostic feedback signals, respectively, in compliance with IEC 61000-4-2, IEC61000-4-4, IEC 61000-4-5 requirements. These requirements are satisfied by IPS160H itself and by the U1 component (the external TVS between VCC supply rail and power ground).

A dedicated GUI interface was developed to facilitate the testing of IPS160H functionality. To use the GUI, connect the STEVAL-IFP028V1 to the STEVAL-PCC009V2 with a 30-way flat cable, followed by a USB connection between the STEVAL-PCC009V2 and the PC where the GUI runs.

The GUI can be used to drive the STEVAL-IFP028V1 and monitor the status of the output on the power side, receiving fault information available on the IPS160H DIAG pin.

The STEVAL-IFP028V1 can be operate in an 8 to 60 V range, bearing in mind that the red LED functionality on the DIAG pin is only guaranteed from VCC = 12 V and that for a supply voltage higher than 40 V, J1 must be open to avoid permanent damage to U1.

Finally, the STEVAL-IFP028V1 optimizes thermal performance through a careful layout which includes a dedicated copper area connected to the exposed pad of the PSSO12 package, also acting as a heatsink.

Key Features

  • Operating voltage from 8 to 60 V
  • Operating current up to 2.5 A
  • Programmable cut-off delay time
  • Reverse polarity protection
  • Galvanic isolation
  • Input pins compatible with VCC rails
  • Green LED for channel ON/OFF status
  • Red LED for common diagnostic on:
    • Open load in OFF state
    • Cut-off
    • Thermal protection
    • Red LED functionality on DIAG pin guaranteed from VCC = 12 V
  • Microcontroller interface
  • IEC 61000-4-2, IEC61000-4-4 and IEC 61000-4-5 compliant
  • RoHS compliant
Product Specifications
DescriptionVersionSize
DB2872: Single high side driver based on IPS160H1.0239 KB
Application Notes
DescriptionVersionSize
AN4781: STEVAL-IFP028V1 evaluation board for single high-side driver IPS160H1.0882 KB
Board Manufacturing Specifications
DescriptionVersionSize
STEVAL-IFP028V1 gerber files1.0173 KB
Bill of Materials
DescriptionVersionSize
STEVAL-IFP028V1 BOM1.057 KB
Schematic Packs
DescriptionVersionSize
STEVAL-IFP028V1 schematic1.051 KB
Brochures
DescriptionVersionSize
Products and Solutions for Factory Automation and Control1.03 MB
License Agreement
DescriptionVersionSize
Evaluation products license agreement1.0125 KB
Sample & Buy
Part NumberCore ProductUnit Price (US$) *QuantityECCN (EU)ECCN (US)Country of Origin
STEVAL-IFP028V1IPS160H33.081NECEAR99ITALY
Quality & Reliability
Part NumberPackageGradeRoHS Compliance GradeMaterial Declaration**
STEVAL-IFP028V1CARDIndustrialEcopack2
Single high side driver based on IPS160H STEVAL-IFP028V1
STEVAL-IFP028V1 evaluation board for single high-side driver IPS160H STEVAL-IFP028V1
STEVAL-IFP028V1 evaluation board for single high-side driver IPS160H STEVAL-IFP028V1
STEVAL-IFP028V1 evaluation board for single high-side driver IPS160H STEVAL-IFP028V1
STEVAL-IFP028V1 evaluation board for single high-side driver IPS160H STEVAL-IFP028V1
STEVAL-SPIMD20V1 demonstration kit based on the SPIMD20 integrated motor drive STEVAL-SPIMD20V1
ST-LINK/V2 in-circuit debugger/programmer for STM8 and STM32 ST-LINK-V2