MC10E111: 5.0 V ECL 1:9 Differential Clock Driver

The MC10E/100E111 is a low skew 1-to-9 differential driver, designed with clock distribution in mind. It accepts one signal input, which can be either differential or else single-ended if the VBB output is used. The signal is fanned out to 9 identical differential outputs. An enable input is also provided. A HIGH disables the device by forcing all Q outputs LOW and all Qbar outputs HIGH. The device is specifically designed, modeled and produced with low skew as the key goal. Optimal design and layout serve to minimize gate to gate skew within-device, and empirical modeling is used to determine process control limits that ensure consistent tpd distributions from lot to lot. The net result is a dependable, guaranteed low skew device. To ensure that the tight skew specification is met it is necessary that both sides of the differential output are terminated into 50 , even if only one side is being used. In most applications, all nine differential pairs will be used and therefore terminated. In the case where fewer than nine pairs are used, it is necessary to terminate at least the output pairs on the same package side (i.e. sharing the same VCCO ) as the pair(s) being used on that side, in order to maintain minimum skew. Failure to do this will result in small degradations of propagation delay (on the order of 10-20 ps) of the output(s) being used which, while not being catastrophic to most designs, will mean a loss of skew margin. The VBB pin, an internally generated voltage supply, is available to this device only. For single-ended input conditions, the unused differential input is connected to VBB as a switching reference voltage. VBB may also rebias AC coupled inputs. When used, decouple VBB and VCC via a 0.01 F capacitor and limit current sourcing or sinking to 0.5 mA. When not used, VBB should be left open. The 100 Series contains temperature

特性
  • Guaranteed Skew Spec
  • Differential Design
  • VBB Output
  • PECL Mode Operating Range: VCC = 4.2 V to 5.7 V with VEE = 0 V
  • NECL Mode Operating Range: VCC = 0 V with VEE = -4.2 V to -5.7 V
  • Internal Input Pulldown Resistors
  • ESD Protection: > 3 KV HBM
  • Meets or Exceeds JEDEC Spec EIA/JESD78 IC Latchup Test
  • Moisture Sensitivity Level 1 (For Additional Information, see Application Note AND8003/D)
  • Flammability Rating: UL-94 code V-0 @ 1/8 inch, Oxygen Index 28 to 34
  • Transistor Count = 178 devices
  • Pb-Free Packages are Available
封装
应用注释 (17)
Document TitleDocument ID/SizeRevisionRevision Date
AC Characteristics of ECL DevicesAND8090/D (896.0kB)1
Clock Generation and Clock and Data Marking and Ordering Information GuideAND8002/D (71kB)12
Clock Management Design Using Low Skew and Low Jitter DevicesTND301/D (205.0kB)0
Designing with PECL (ECL at +5.0 V)AN1406/D (105.0kB)2
ECL Clock Distribution TechniquesAN1405/D (54.0kB)1
ECLinPS and ECLinPS Lite SPICE I/O Modeling KitAN1503/D (120.0kB)6
ECLinPS™ Circuit Performance at Non-Standard VIH LevelsAN1404/D (51.0kB)1
Interfacing Between LVDS and ECLAN1568/D (121.0kB)11
Interfacing with ECLinPSAND8066/D (72kB)3
Metastability and the ECLinPS FamilyAN1504/D (103.0kB)3
Odd Number Divide By Counters with 50% Outputs and Synchronous ClocksAND8001/D (90.0kB)0
Phase Lock Loop General OperationsAND8040/D (64.0kB)3
Storage and Handling of Drypack Surface Mount DeviceAND8003/D (49kB)2Mar, 2016
Termination of ECL Logic DevicesAND8020/D (176.0kB)6
The ECL Translator GuideAN1672/D (142.0kB)12
Thermal Analysis and Reliability of WIRE BONDED ECLAND8072/D (119.0kB)5
Using Wire-OR Ties in ECLInPS™ DesignsAN1650/D (1130.0kB)3
数据表 (1)
Document TitleDocument ID/SizeRevisionRevision Date
5 V ECL 1:9 Differential Clock DriverMC10E111/D (168kB)17Jul, 2016
仿真模型 (1)
Document TitleDocument ID/SizeRevisionRevision Date
IBIS Model for MC10E111FN with VEE at 5.0 VMC10E111FN_50.IBS (6.0kB)0
封装图纸 (1)
Document TitleDocument ID/SizeRevision
28 LEAD PLCC776-02 (67.7kB)F
产品订购型号
产品状况Compliance封装MSL*容器预算价格 (1千个数量的单价)
MC10E111FNGActivePb-free Halide freePLCC-28776-023Tube37联系BDTIC
MC10E111FNR2GActivePb-free Halide freePLCC-28776-023Tape and Reel500联系BDTIC
订购产品技术参数
ProductTypeChannelsInput / Output RatioInput LevelOutput LevelVCC Typ (V)tJitterRMS Typ (ps)tskew(o-o) Max (ps)tpd Typ (ns)tR & tF Max (ps)fmaxClock Typ (MHz)fmaxData Typ (Mbps)
MC10E111FNGBuffer11:9ECLECL5<1750.53650800
MC10E111FNR2GBuffer11:9ECLECL5<1750.53650800
5 V ECL 1:9 Differential Clock Driver (168kB) MC10E111
AC Characteristics of ECL Devices NB100LVEP91
Clock Generation and Clock and Data Marking and Ordering Information Guide NB100LVEP91
Clock Management Design Using Low Skew and Low Jitter Devices MC10H604
Designing with PECL (ECL at +5.0 V) NB100LVEP91
ECL Clock Distribution Techniques NB100LVEP91
ECLinPS and ECLinPS Lite SPICE I/O Modeling Kit MC100EP91
ECLinPS™ Circuit Performance at Non-Standard VIH Levels MC10E195
Interfacing Between LVDS and ECL NB100ELT23L
Interfacing with ECLinPS NB100LVEP91
Metastability and the ECLinPS Family MC10EPT20
Odd Number Divide By Counters with 50% Outputs and Synchronous Clocks NUP4201
Phase Lock Loop General Operations MC10H604
Storage and Handling of Drypack Surface Mount Device NB3U23C
Termination of ECL Logic Devices NB100LVEP91
The ECL Translator Guide NB100LVEP91
Thermal Analysis and Reliability of WIRE BONDED ECL NB100LVEP91
Using Wire-OR Ties in ECLInPS™ Designs MC10H351
IBIS Model for MC10E111FN with VEE at 5.0 V MC10E111
28 LEAD PLCC MC10H604