产品特性

• DC – 40 MIPS (40 MIPS @ 3.0-3.6V, -40°C to +125°C)
• Industrial temperature range (-40°C to +85°C)
• Extended temperature range (-40°C to +125°C)
• High temperature range (-40°C to +150°C)
• Modified Harvard architecture
• C compiler optimized instruction set
• 16-bit wide data path
• 24-bit wide instructions
• Linear program memory addressing up to 4M instruction words
• Linear data memory addressing up to 64 Kbytes
• 83 base instructions: mostly 1 word/1 cycle
• Sixteen 16-bit General Purpose Registers
• Two 40-bit accumulators: With rounding and saturation options
• With rounding and saturation options
• Flexible and powerful addressing modes: Indirect, Modulo and Bit-Reversed ]
• Indirect, Modulo and Bit-Reversed
• Software stack
• 16 x 16 fractional/integer multiply operations
• 32/16 and 16/16 divide operations
• Single-cycle multiply and accumulate: Accumulator write back for DSP operations Dual data fetch
• Accumulator write back for DSP operations
• Dual data fetch
• Up to ±16-bit shifts for up to 40-bit data
• 8-channel hardware DMA
• 2 Kbytes dual ported DMA buffer area (DMA RAM) to store data transferred via DMA: Allows data transfer between RAM and a peripheral while CPU is executing code (no cycle stealing)
• Allows data transfer between RAM and a peripheral while CPU is executing code (no cycle stealing)
• Most peripherals support DMA Interrupt Controller
• 5-cycle latency
• 118 interrupt vectors
• Up to 67 available interrupt sources
• Up to 5 external interrupts
• 7 programmable priority levels
• 5 processor exceptions
• Wake-up/Interrupt-on-Change on up to 24 pins
• Output pins can drive from 3.0V to 3.6V
• All digital input pins are 5V tolerant
• 4 mA sink on all I/O pins
• Flexible clock options: External, crystal, resonator, internal RC Fully integrated PLL Extremely low jitter PLL
• External, crystal, resonator, internal RC
• Fully integrated PLL
• Extremely low jitter PLL
• Power-up Timer
• Oscillator Start-up Timer/Stabilizer
• Watchdog Timer with its own RC oscillator
• Fail-Safe Clock Monitor
• Reset by multiple sources Power Management
• On-chip 2.5V voltage regulator
• Switch between clock sources in real time
• Idle, Sleep and Doze modes with fast wake-up
• Timer/Counters, up to nine 16-bit timers: Can pair up to make four 32-bit timers 1 timer runs as Real-Time Clock with external 32.768 kHz oscillator Programmable prescaler
• Can pair up to make four 32-bit timers
• 1 timer runs as Real-Time Clock with external 32.768 kHz oscillator
• Programmable prescaler
• Input Capture (up to 8 channels): Capture on up, down or both edges 16-bit capture input functions 4-deep FIFO on each capture
• Capture on up, down or both edges
• 16-bit capture input functions
• 4-deep FIFO on each capture
• Output Compare (up to 8 channels): Single or Dual 16-Bit Compare mode 16-bit Glitchless PWM mode
• Single or Dual 16-Bit Compare mode
• 16-bit Glitchless PWM mode
• 3-wire SPI (up to 2 modules): Framing supports I/O interface to simple codecs Supports 8-bit and 16-bit data Supports all serial clock formats and sampling modes
• Framing supports I/O interface to simple codecs
• Supports 8-bit and 16-bit data
• Supports all serial clock formats and sampling modes
• I2C™ (up to 2 modules): Full Multi-Master Slave mode support 7-bit and 10-bit addressing Bus collision detection and arbitration Integrated signal conditioning Slave address masking
• Full Multi-Master Slave mode support
• 7-bit and 10-bit addressing
• Bus collision detection and arbitration
• Integrated signal conditioning
• Slave address masking
• UART (up to 2 modules): Interrupt on address bit detect Interrupt on UART error Wake-up on Start bit from Sleep mode 4-character TX and RX FIFO buffers LIN bus support IrDA® encoding and decoding in hardware High-Speed Baud mode Hardware Flow Control with CTS and RTS
• Interrupt on address bit detect
• Interrupt on UART error
• Wake-up on Start bit from Sleep mode
• 4-character TX and RX FIFO buffers
• LIN bus support
• IrDA® encoding and decoding in hardware
• High-Speed Baud mode
• Hardware Flow Control with CTS and RTS
• Data Converter Interface (DCI) module: Codec interface Supports I2S and AC’97 protocols Up to 16-bit data words, up to 16 words per frame 4-word deep TX and RX buffers
• Codec interface
• Supports I2S and AC’97 protocols
• Up to 16-bit data words, up to 16 words per frame
• 4-word deep TX and RX buffers
• Enhanced CAN (ECAN™ module) 2.0B active (up to 2 modules): Up to 8 transmit and up to 32 receive buffers 16 receive filters and 3 masks Loopback, Listen Only and Listen All Messages modes for diagnostics and bus monitoring Wake-up on CAN message Automatic processing of Remote Transmission Requests FIFO mode using DMA DeviceNet™ addressing support
• Up to 8 transmit and up to 32 receive buffers
• 16 receive filters and 3 masks
• Loopback, Listen Only and Listen All Messages modes for diagnostics and bus monitoring
• Wake-up on CAN message
• Automatic processing of Remote Transmission Requests
• FIFO mode using DMA
• DeviceNet™ addressing support
• Up to two ADC modules in a device
• 10-bit, 1.1 Msps or 12-bit, 500 Ksps conversion: 2, 4 or 8 simultaneous samples Up to 32 input channels with auto-scanning Conversion start can be manual or synchronized with 1 of 4 trigger sources Conversion possible in Sleep mode - ±2 LSb max integral nonlinearity ±1 LSb max differential nonlinearity CMOS Flash Technology
• 2, 4 or 8 simultaneous samples
• Up to 32 input channels with auto-scanning
• Conversion start can be manual or synchronized with 1 of 4 trigger sources
• Conversion possible in Sleep mode - ±2 LSb max integral nonlinearity
• ±1 LSb max differential nonlinearity CMOS Flash Technology
• Low-power, high-speed Flash technology
• Fully static design
• 3.3V (±10%) operating voltage
• Industrial temperature
• Low-power consumption

技术参数