dsPIC33FJ64MC204

产品特性
  • Up to 40 MIPS operation (at 3.0-3.6V): Industrial temperature range (-40°C to +85°C) Extended temperature range (-40°C to +125°C) High-Performance DSC CPU: Modified Harvard architecture C compiler optimized instruction set 16-bit wide data path 24-bit wide instructions Linear program memory addressing up to 4M instruction words Linear data memory addressing up to 64 Kbytes 83 base instructions: mostly 1 word/1 cycle Two 40-bit accumulators with rounding and saturation options Flexible and powerful addressing modes: Indirect Modulo Bit-Reversed Software stack 16 x 16 fractional/integer multiply operations 32/16 and 16/16 divide operations Single-cycle multiply and accumulate: Accumulator write back for DSP operations Dual data fetch Up to ±16-bit shifts for up to 40-bit data On-Chip Flash and SRAM: Flash program memory Data SRAM Boot, Secure, and General Security for program Flash Direct Memory Access (DMA): 8-channel hardware DMA Up to 2 Kbytes dual ported DMA buffer area (DMA RAM) to store data transferred via DMA: Allows data transfer between RAM and a peripheral while CPU is executing code (no cycle stealing) Most peripherals support DMA Timers/Capture/Compare/PWM: Timer/Counters, up to five 16-bit timers: Can pair up to make two 32-bit timers One timer runs as a Real-Time Clock with an external 32.768 kHz oscillator Programmable prescaler Input Capture (up to four channels): Capture on up, down or both edges 16-bit capture input functions 4-deep FIFO on each capture Output Compare (up to four channels): Single or Dual 16-bit Compare mode 16-bit Glitchless PWM mode Hardware Real-Time Clock/Calendar (RTCC): Provides clock, calendar, and alarm functions Interrupt Controller: 5-cycle latency 118 interrupt vectors Up to 53 available interrupt sources Up to three external interrupts Seven programmable priority levels Five processor exceptions Digital I/O: Peripheral pin Select functionality Up to 35 programmable digital I/O pins Wake-up/Interrupt-on-Change for up to 21 pins Output pins can drive from 3.0V to 3.6V Up to 5V output with open drain configuration All digital input pins are 5V tolerant 4 mA sink on all I/O pins System Management: Flexible clock options: External, crystal, resonator, internal RC Fully integrated Phase-Locked Loop (PLL) Extremely low jitter PLL Power-up Timer Oscillator Start-up Timer/Stabilizer Watchdog Timer with its own RC oscillator Fail-Safe Clock Monitor Reset by multiple sources Power Management: On-chip 2.5V voltage regulator Switch between clock sources in real time Idle, Sleep, and Doze modes with fast wake-up Analog-to-Digital Converters (ADCs): 10-bit, 1.1 Msps or 12-bit, 500 Ksps conversion: Two and four simultaneous samples (10-bit ADC) Up to nine input channels with auto-scanning Conversion start can be manual or synchronized with one of four trigger sources Conversion possible in Sleep mode ±2 LSb max integral nonlinearity ±1 LSb max differential nonlinearity Comparator Module: Two analog comparators with programmable input/output configuration CMOS Flash Technology: Low-power, high-speed Flash technology Fully static design 3.3V (±10%) operating voltage Industrial and Extended temperature Low power consumption Motor Control Peripherals: 6-channel 16-bit Motor Control PWM: Three duty cycle generators Independent or Complementary mode Programmable dead time and output polarity Edge-aligned or center-aligned Manual output override control One Fault input Trigger for ADC conversions PWM frequency for 16-bit resolution (@ 40 MIPS) = 1220 Hz for Edge-Aligned mode, 610 Hz for Center-Aligned mode PWM frequency for 11-bit resolution (@ 40 MIPS) = 39.1 kHz for Edge-Aligned mode, 19.55 kHz for Center-Aligned mode 2-channel 16-bit Motor Control PWM: One duty cycle generator Independent or Complementary mode Programmable dead time and output polarity Edge-aligned or center-aligned Manual output override control One Fault input Trigger for ADC conversions PWM frequency for 16-bit resolution (@ 40 MIPS) = 1220 Hz for Edge-Aligned mode, 610 Hz for Center-Aligned mode PWM frequency for 11-bit resolution (@ 40 MIPS) = 39.1 kHz for Edge-Aligned mode, 19.55 kHz for Center-Aligned mode 2-Quadrature Encoder Interface module: Phase A, Phase B, and index pulse input 16-bit up/down position counter C
  • Industrial temperature range (-40°C to +85°C)
  • Extended temperature range (-40°C to +125°C)
  • Modified Harvard architecture
  • C compiler optimized instruction set
  • 16-bit wide data path
  • 24-bit wide instructions
  • Linear program memory addressing up to 4M instruction words
  • Linear data memory addressing up to 64 Kbytes
  • 83 base instructions: mostly 1 word/1 cycle
  • Two 40-bit accumulators with rounding and saturation options
  • Flexible and powerful addressing modes: Indirect Modulo Bit-Reversed
  • Indirect
  • Modulo
  • Bit-Reversed
  • Software stack
  • 16 x 16 fractional/integer multiply operations
  • 32/16 and 16/16 divide operations
  • Single-cycle multiply and accumulate: Accumulator write back for DSP operations Dual data fetch
  • Accumulator write back for DSP operations
  • Dual data fetch
  • Up to ±16-bit shifts for up to 40-bit data
  • Flash program memory
  • Data SRAM
  • Boot, Secure, and General Security for program Flash
  • 8-channel hardware DMA
  • Up to 2 Kbytes dual ported DMA buffer area (DMA RAM) to store data transferred via DMA: Allows data transfer between RAM and a peripheral while CPU is executing code (no cycle stealing)
  • Allows data transfer between RAM and a peripheral while CPU is executing code (no cycle stealing)
  • Most peripherals support DMA
  • Timer/Counters, up to five 16-bit timers: Can pair up to make two 32-bit timers One timer runs as a Real-Time Clock with an external 32.768 kHz oscillator Programmable prescaler
  • Can pair up to make two 32-bit timers
  • One timer runs as a Real-Time Clock with an external 32.768 kHz oscillator
  • Programmable prescaler
  • Input Capture (up to four channels): Capture on up, down or both edges 16-bit capture input functions 4-deep FIFO on each capture
  • Capture on up, down or both edges
  • 16-bit capture input functions
  • 4-deep FIFO on each capture
  • Output Compare (up to four channels): Single or Dual 16-bit Compare mode 16-bit Glitchless PWM mode
  • Single or Dual 16-bit Compare mode
  • 16-bit Glitchless PWM mode
  • Hardware Real-Time Clock/Calendar (RTCC): Provides clock, calendar, and alarm functions
  • Provides clock, calendar, and alarm functions
  • 5-cycle latency
  • 118 interrupt vectors
  • Up to 53 available interrupt sources
  • Up to three external interrupts
  • Seven programmable priority levels
  • Five processor exceptions
  • Peripheral pin Select functionality
  • Up to 35 programmable digital I/O pins
  • Wake-up/Interrupt-on-Change for up to 21 pins
  • Output pins can drive from 3.0V to 3.6V
  • Up to 5V output with open drain configuration
  • All digital input pins are 5V tolerant
  • 4 mA sink on all I/O pins
  • Flexible clock options: External, crystal, resonator, internal RC Fully integrated Phase-Locked Loop (PLL) Extremely low jitter PLL
  • External, crystal, resonator, internal RC
  • Fully integrated Phase-Locked Loop (PLL)
  • Extremely low jitter PLL
  • Power-up Timer
  • Oscillator Start-up Timer/Stabilizer
  • Watchdog Timer with its own RC oscillator
  • Fail-Safe Clock Monitor
  • Reset by multiple sources
  • On-chip 2.5V voltage regulator
  • Switch between clock sources in real time
  • Idle, Sleep, and Doze modes with fast wake-up
  • 10-bit, 1.1 Msps or 12-bit, 500 Ksps conversion: Two and four simultaneous samples (10-bit ADC) Up to nine input channels with auto-scanning Conversion start can be manual or synchronized with one of four trigger sources Conversion possible in Sleep mode ±2 LSb max integral nonlinearity ±1 LSb max differential nonlinearity
  • Two and four simultaneous samples (10-bit ADC)
  • Up to nine input channels with auto-scanning
  • Conversion start can be manual or synchronized with one of four trigger sources
  • Conversion possible in Sleep mode
  • ±2 LSb max integral nonlinearity
  • ±1 LSb max differential nonlinearity
  • Two analog comparators with programmable input/output configuration
  • Low-power, high-speed Flash technology
  • Fully static design
  • 3.3V (±10%) operating voltage
  • Industrial and Extended temperature
  • Low power consumption
  • 6-channel 16-bit Motor Control PWM: Three duty cycle generators Independent or Complementary mode Programmable dead time and output polarity Edge-aligned or center-aligned Manual output override control One Fault input Trigger for ADC conversions PWM frequency for 16-bit resolution (@ 40 MIPS) = 1220 Hz for Edge-Aligned mode, 610 Hz for Center-Aligned mode PWM frequency for 11-bit resolution (@ 40 MIPS) = 39.1 kHz for Edge-Aligned mode, 19.55 kHz for Center-Aligned mode
  • Three duty cycle generators
  • Independent or Complementary mode
  • Programmable dead time and output polarity
  • Edge-aligned or center-aligned
  • Manual output override control
  • One Fault input
  • Trigger for ADC conversions
  • PWM frequency for 16-bit resolution (@ 40 MIPS) = 1220 Hz for Edge-Aligned mode, 610 Hz for Center-Aligned mode
  • PWM frequency for 11-bit resolution (@ 40 MIPS) = 39.1 kHz for Edge-Aligned mode, 19.55 kHz for Center-Aligned mode
  • 2-channel 16-bit Motor Control PWM: One duty cycle generator Independent or Complementary mode Programmable dead time and output polarity Edge-aligned or center-aligned Manual output override control One Fault input Trigger for ADC conversions PWM frequency for 16-bit resolution (@ 40 MIPS) = 1220 Hz for Edge-Aligned mode, 610 Hz for Center-Aligned mode PWM frequency for 11-bit resolution (@ 40 MIPS) = 39.1 kHz for Edge-Aligned mode, 19.55 kHz for Center-Aligned mode
  • One duty cycle generator
  • Independent or Complementary mode
  • Programmable dead time and output polarity
  • Edge-aligned or center-aligned
  • Manual output override control
  • One Fault input
  • Trigger for ADC conversions
  • PWM frequency for 16-bit resolution (@ 40 MIPS) = 1220 Hz for Edge-Aligned mode, 610 Hz for Center-Aligned mode
  • PWM frequency for 11-bit resolution (@ 40 MIPS) = 39.1 kHz for Edge-Aligned mode, 19.55 kHz for Center-Aligned mode
  • 2-Quadrature Encoder Interface module: Phase A, Phase B, and index pulse input 16-bit up/down position counter C
  • Phase A, Phase B, and index pulse input
  • 16-bit up/down position counter
  • C
技术参数
Parameter Name Value Value
Architecture 16-bit 16-bit
CPU Speed (MIPS) 40 40
Memory Type Flash Flash
Program Memory (KB) 64 64
RAM Bytes 8,192 8,192
Temperature Range C -40 to 125 -40 to 125
Operating Voltage Range (V) 3 to 3.6 3 to 3.6
I/O Pins 35 35
Pin Count 44 44
System Management Features BOR BOR
POR Yes Yes
WDT Yes Yes
nanoWatt Features Fast Wake/Fast Control Fast Wake/Fast Control
Digital Communication Peripherals 2-UART2-SPI1-I2C 2-UART2-SPI1-I2C
Comparators 2 2
USB (ch, speed, compliance) 0, None, 0, None,
CAN (#, type) 0 None 0 None
Capture/Compare/PWM Peripherals 4/4 4/4
PWM Resolution bits 16 16
Motor Control PWM Channels 8 8
Quadrature Encoder Interface (QEI) 2 2
Timers 5 x 16-bit 2 x 32-bit 5 x 16-bit 2 x 32-bit
Parallel Port PMP PMP
DMA 8 8
Cap Touch Channels 9 9
文档资料
dsPIC33FJ32MC302/304, dsPIC33FJ64MCX02/X04 and dsPIC33FJ128MCX02/X04 Data SheetData Sheets04/19/20126397KB
dsPIC33FJ32MC302/304, dsPIC33FJ64MCX02/X04, dsPIC33FJ128MCX02/X04 Family ErrataErrata12/02/2015166KB
16-bit MCU and DSC Programmer's Reference ManualProgramming Specification02/25/201310777KB
dsPIC33F/PIC24H Flash Programming SpecificationProgramming Specification10/19/20101322KB
AN1017 - Sinusoidal Control of PMSM Motors with dsPIC30F / dsPIC33F/ dsPIC33E DSCAppNote06/27/2011313KB
AN1044 - Data Encryption Routines for PIC24 and dsPIC DevicesAppNote03/01/2013347KB
AN1045 - File I/O Functions Using Microchip's Memory Disk Drive File System LibraryAppNote05/02/2014350KB
AN1069 - Using C30 Compiler and the SPI module to Interface EEPROMs with dsPIC33F and PIC24FAppNote11/27/2007370KB
AN1071 - IrDA Standard Stack for Microchip 16-Bit and 32-bit MCUsAppNote12/07/2010716KB
AN1078 - Sensorless Field Oriented Control of a PMSMAppNote04/04/2010474KB
AN1079 - Using the C30 Compiler and the I2C? Peripheral to Interface Serial EEPROMs with dsPIC33FAppNote03/16/2007515KB
AN1094 - Bootloader for dsPIC30F/33F and PIC24F/24H DevicesAppNote05/18/2007413KB
AN1096 - Using the C30 Compiler to Interface SPI Serial EEPROMs with dsPIC33AppNote11/08/2007367KB
AN1100 - Using the C30 Compiler to Interface Serial EEPROMs with dsPIC33FAppNote06/28/2007416KB
AN1106 - AN1106, Power Factor Correction in Power Conversion Applications Using the dsPIC® DSCAppNote11/13/20071021KB
AN1115 - Implementing Digital Lock-In Amplifiers Using the dsPIC DSCAppNote10/19/2007392KB
AN1160 - Sensorless BLDC Control with Back-EMF Filtering Using a Majority FunctionAppNote11/10/2012693KB
AN1162 - Sensorless Field Oriented Control (FOC) of an AC Induction Motor (ACIM)AppNote07/03/2012766KB
AN1204 - Microchip MiWi P2P Wireless ProtocolAppNote11/16/2010417KB
AN1206 - Sensorless Field Oriented Control (FOC) of an AC Induction Motor (ACIM) Using Field WeakeningAppNote06/13/2008264KB
AN1208 - Integrated Power Factor Correction (PFC) and Sensorless Field Oriented Control (FOC) SystemAppNote06/17/2008771KB
AN1210 - Using External Memory with PIC24F/24H/dsPIC33F DevicesAppNote07/15/2008240KB
AN1227 - Using a Keyboard with the Microchip Graphics LibraryAppNote03/28/2010150KB
AN1229 - Class B Safety Software Library for PIC MCUs and dsPIC DSCsAppNote04/24/2012439KB
AN1236 - Using C30 and a Timer to Interface dsPIC33 DSCs and PIC24 MCUs with UNI/O(R) Bus-Compatible Serial EEPROMsAppNote10/30/2008264KB
AN1249 - ECAN Operation with DMA on dsPIC33F and PIC24H DevicesAppNote02/13/2009460KB
AN1292 - Sensorless Field Oriented Control (FOC) for a Permanent Magnet Synchronous Motor (PMSM)Using a PLL Estimator and Field Weakening (FW)AppNote06/30/2011440KB
AN1299 - Single-Shunt Three-Phase Current Reconstruction Algorithm for Sensorless FOC of a PMSMAppNote11/18/2009913KB
AN1307 - Stepper Motor Control with dsPIC DSCsAppNote10/07/2011310KB
AN699 - Anti-Aliasing, Analog Filters for Data Acquisition SystemsAppNote07/26/1999171KB
AN887 - AC Induction Motor FundamentalsAppNote12/18/2003427KB
AN901 - Using the dsPIC30F for Sensorless BLDC ControlAppNote06/06/2011940KB
AN908 - Using the dsPIC30F / dsPIC33F for Vector Control of an ACIMAppNote12/06/20071765KB
AN957 - Sensored BLDC Motor Control Using dsPIC30F2010AppNote06/23/2005869KB
AN984 - An Introduction to AC Induction Motor Control Using the dsPIC30F / dsPIC33F DSCAppNote06/27/2005338KB
AN992 - Sensorless BLDC Motor Control Using dsPIC30F2010AppNote06/06/20111027KB
16-bit Embedded Control Solutions BrochureBrochures06/29/20157978KB
Electronic Solutions for Medical and FitnessBrochures09/10/201410216KB
Motor Control and Drive BrochureBrochures07/19/20168104KB
MPLAB® X IDE Product OverviewSell Sheets07/11/2011182KB
dsPIC33/PIC24 FRM, I2CReference Manual03/18/2014668KB
dsPIC33/PIC24 FRM, Output CompareReference Manual03/13/2014322KB
dsPIC33/PIC24 FRM, Serial Peripheral Interface (SPI)Reference Manual05/28/2014281KB
dsPIC33/PIC24 FRM, UARTReference Manual03/14/2014467KB
Section 02. CPU - dsPIC33F FRMReference Manual01/03/2014664KB
Section 03. Data Memory - dsPIC33F/PIC24H FRMReference Manual01/06/2014227KB
Section 04. Program Memory - dsPIC33F/PIC24H FRMReference Manual01/06/2014332KB
Section 05. Flash Programming - dsPIC33F/PIC24H FRMReference Manual01/03/2014348KB
Section 08. Reset - dsPIC33F FRMReference Manual01/06/2014146KB
Section 10. I/O Ports - dsPIC33F/PIC24H FRMReference Manual01/03/2014321KB
Section 11. Timers - dsPIC33F/PIC24H FRMReference Manual01/03/2014446KB
Section 12. Input Capture - dsPIC33F FRMReference Manual01/03/2014211KB
Section 14. Motor Control PWM - dsPIC33F/PIC24H FRMReference Manual01/03/2014630KB
Section 15. Quadrature Encoder Interface (QEI) - dsPIC33F FRMReference Manual01/03/2014320KB
Section 16. Analog-to-Digital Converter (ADC) - dsPIC33F/PIC24H FRMReference Manual01/03/20141417KB
Section 21. Enhanced Controller Area Network (ECAN) - dsPIC33F/PIC24H FRMReference Manual01/03/20141088KB
Section 23. CodeGuard Security - dsPIC33F/PIC24H FRMReference Manual01/03/20141032KB
Section 24. Programming and Diagnostics - dsPIC33F/PIC24H FRMReference Manual01/03/2014392KB
Section 25. Device Configuration - dsPIC33F/PIC24H FRMReference Manual01/06/2014132KB
Section 26. Development Tool Support - dsPIC33F FRMReference Manual01/06/2014130KB
Section 30. I/O Ports with Peripheral Pin Select (PPS) - dsPIC33F/PIC24H FRMReference Manual01/03/2014530KB
Section 31. Introduction (Part III) - dsPIC33F FRMReference Manual01/03/201494KB
Section 32. Interrupts (Part III) - dsPIC33F/PIC24H FRMReference Manual01/03/2014860KB
Section 33. Audio Digital-to-Analog Converter (DAC) - dsPIC33F FRMReference Manual01/03/2014205KB
Section 34. Comparator - dsPIC33F FRMReference Manual01/03/2014169KB
Section 35. Parallel Master Port (PMP) - dsPIC33F/PIC24H FRMReference Manual02/03/2014514KB
Section 36. Programmable Cyclic Redundancy Check (CRC) - dsPIC33F FRMReference Manual01/03/2014178KB
Section 37. Real-Time Clock and Calendar (RTCC) - dsPIC33F/PIC24H FRMReference Manual01/03/2014494KB
Section 38. Direct Memory Access (DMA) (Part III) - dsPIC33F/PIC24H FRMReference Manual01/03/20141122KB
Section 39. Oscillator (Part III) - dsPIC33F FRMReference Manual01/03/2014440KB
Program Executive RIPE_01b_000033Software12/08/20143KB
dsPICDEM MCSM Development Board Demonstration SoftwareSoftware10/27/20091072KB
dsPIC33FJ64MC204 BSDL FileBoundaryScanBSDL09/22/201411KB
CE100 - Using A/D Converters and DSP Library for Signal FilteringCode Examples08/17/2009425KB
CE101 - Configuring 10-bit A/D Converters for 1MSPS Conversion RateCode Examples09/12/201126KB
CE102 - Performing A/D Conversions in SLEEP (Low-Power) ModeCode Examples08/17/200920KB
CE103 - Implementing DOZE Mode for Dynamic CPU Power ControlCode Examples12/10/200933KB
CE104 - Dynamic Clock Switching for Low Power OperationCode Examples08/17/200916KB
CE105 - Address Error Traps for Easy DebuggingCode Examples08/17/200913KB
CE106 - Math Error Traps for Robust OperationCode Examples12/10/200931KB
CE107 - Stack Error Traps for Easy DebuggingCode Examples08/17/200915KB
CE108 - Oscillator Failure Traps and Failsafe Clock MonitoringCode Examples08/17/200916KB
CE109 - Run-Time Self Programming of FLASH Program MemoryCode Examples08/17/200920KB
CE110 - Dynamic Tuning of Internal Fast RCCode Examples08/17/200917KB
CE111 - External Interrupt Pins Configuration and UseCode Examples08/17/200918KB
CE112 - Fast Wake-up From Sleep ModeCode Examples08/17/200911KB
CE113 - Timer1 used in Real-Time Clock ApplicationsCode Examples08/17/200933KB
CE114 - Using the DMA with the UART in Loopback modeCode Examples08/17/200914KB
CE115 - Example of Handling a DMA TrapCode Examples12/10/200937KB
CE116 - Using the DMA with the SPI moduleCode Examples08/17/200919KB
CE117 - Using the DMA with DCI peripheral for I2S driverCode Examples09/12/201123KB
CE118 - Using FIR Filters From dsPIC Filter Design and DSP LibraryCode Examples08/17/200918KB
CE119 Interfacing to I2C Serial EEPROM using I2C peripheralCode Examples08/17/200917KB
CE120 A/D Conversions with Scanning through selected Analog Inputs with DMACode Examples08/17/200925KB
CE121 A/D Conversions with Scanning through selected Analog Inputs without DMACode Examples08/17/200921KB
CE122 - ADC Alternate SamplingCode Examples08/17/200920KB
CE123 - CodeGuard(TM) Security: segment creation and code placementCode Examples09/15/200929KB
CE124 - CodeGuard(TM) Security: Program flow changes between segmentsCode Examples09/15/200936KB
CE127 - Crosswire Communication between ECAN 1 and ECAN 2 modulesCode Examples08/17/200945KB
CE128 - ECAN FIFO Receive ExampleCode Examples04/27/200950KB
CE129 - ECAN Remote Transmission RequestCode Examples08/17/200944KB
CE135 - SPI DemoCode Examples08/17/200920KB
CE136 - SPI without DMACode Examples08/17/200931KB
CE137 - UART without DMACode Examples08/17/200913KB
CE138 - SPI with two slavesCode Examples12/10/200945KB
CE139 - 10-bit ADC Sampling at 2.2MSPSCode Examples12/10/2009150KB
CE140 - Inverse tangent operation using CORDIC iterative approximationCode Examples12/10/200943KB
CE141 - SPI with Framed modeCode Examples12/10/200946KB
CE142 - Open Drain configurationCode Examples12/10/200942KB
CE143 - Using Timer1 for Period InterruptsCode Examples08/17/200955KB
CE145 - Using I2C module as a Slave deviceCode Examples12/10/200932KB
CE146 - Adaptive Notch FilterCode Examples12/10/200937KB
CE147 - Signal Matching using Coherence Function Cross Spectral DensityCode Examples12/10/200974KB
CE148 - ADC Sampling with DMA and FIR Filtering - Apps include Circuit BreakersCode Examples08/17/200956KB
CE149 - Signal generation, fractional sampling rate, interpolation, decimationCode Examples08/17/200931KB
CE150 - JPEG Entropy CodingCode Examples08/17/200916KB
CE151 - CRC GenerationCode Examples12/10/200924KB
CE152 - Parallel Master Port (PMP) ExampleCode Examples12/10/200934KB
CE153 - RTCCCode Examples08/17/200912KB
CE154 - ADC to DAC LoopbackCode Examples10/24/201349KB
CE155 - Real-Time Data Monitoring (RTDM) ExampleCode Examples12/10/20091223KB
16-bit CPU Self-test LibrarySoftware Library06/20/2015
dsPIC DSC DTMF Generation/Detection LibrariesSoftware Library08/12/200833KB
dsPIC FSK Generation LibrarySoftware Library12/19/200730KB
Hardware Conditioning of Sensor SignalsWebinars01/27/201057070KB
dsPICDEM MCHV Development System Users GuideApplication Maestro10/13/20092711KB
dsPICDEM MCSM Development Board Users GuideApplication Maestro10/27/20091484KB
CE125 - CodeGuard(TM) Security: Secure Segment ErasedsPIC33F code examples09/13/200726KB
CE144 - CodeGuard Application ExampledsPIC33F code examples09/13/2007327KB
dsPIC33FJ128GP804 and PIC24HJ128GP504 PIM Information Sheet for Graphics AppsPin Maps10/26/2009511KB
dsPIC33FJ128MC804 PIM Information SheetPin Maps10/28/2008301KB
In-Circuit Debugging Interface Options with dsPIC DSCQuick Start Guides09/19/2005110KB
订购型号
Part NumberLeadsPackage TypeTemp RangePacking1+26+100+1000+5000+
DSPIC33FJ64MC204-E/ML44QFN-40C to +125CTUBE5.254.814.364.013.81
DSPIC33FJ64MC204-E/PT44TQFP-40C to +125CTRAY5.134.704.263.923.73
DSPIC33FJ64MC204-I/ML44QFN-40C to +85CTUBE4.784.383.973.653.47
DSPIC33FJ64MC204-I/PT44TQFP-40C to +85CTRAY4.664.283.873.563.39
DSPIC33FJ64MC204T-E/ML44QFN-40C to +125CT/R5.004.884.764.394.17
DSPIC33FJ64MC204T-E/PT44TQFP-40C to +125CT/R4.794.684.564.204.00
DSPIC33FJ64MC204T-I/ML44QFN-40C to +85CT/R4.834.434.013.693.51
DSPIC33FJ64MC204T-I/PT44TQFP-40C to +85CT/R4.714.323.913.603.42
相关开发工具
相类似产品
ProductPinsFlashRAMPrice5KNotes
dsPIC33FJ128MC202281288,192$3.57DSP, HS-PWM
dsPIC33FJ128MC204441288,192$3.68DSP, HS-PWM
dsPIC33FJ128MC8022812816,384$3.82DSP, CAN, HS-PWM
dsPIC33FJ128MC8044412816,384$4.23DSP, CAN, HS-PWM
dsPIC33FJ32MC20228322,048$2.60DSP, HS-PWM
dsPIC33FJ32MC20444322,048$2.76DSP, HS-PWM
dsPIC33FJ32MC30228324,096$2.87DSP, HS-PWM
dsPIC33FJ32MC30444324,096$3.12DSP, HS-PWM
dsPIC33FJ64MC20228648,192$3.29DSP, HS-PWM
dsPIC33FJ64MC20444648,192$3.39DSP, HS-PWM
dsPIC33FJ64MC802286416,384$3.50DSP, CAN, HS-PWM
dsPIC33FJ64MC804446416,384$3.89DSP, CAN, HS-PWM
器件无铅环保信息
PartNumberDeviceWeightShippingWeightLeadCountPackageTypePackageWidthSolderCompositionJEDECIndicatorRoHSChinaEFUP
DSPIC33FJ64MC204T-E/PT0.2733000.74833344TQFP10x10x1mmMatte Tine3
DSPIC33FJ64MC204T-I/PT0.2733000.74833344TQFP10x10x1mmMatte Tine3
DSPIC33FJ64MC204-E/PT0.2733001.18750044TQFP10x10x1mmMatte Tine3
DSPIC33FJ64MC204-I/PT0.2733001.18750044TQFP10x10x1mmMatte Tine3
DSPIC33FJ64MC204-I/ML0.1884000.28888944QFN8x8x0.9mmMatte Tine3
DSPIC33FJ64MC204T-E/ML0.1884000.43750044QFN8x8x0.9mmMatte Tine3
DSPIC33FJ64MC204T-I/ML0.1884000.43750044QFN8x8x0.9mmMatte Tine3
DSPIC33FJ64MC204-E/ML0.1884000.28888944QFN8x8x0.9mmMatte Tine3
dsPIC33FJ32MC302/304, dsPIC33FJ64MCX02/X04 and dsPIC33FJ128MCX02/X04 Data Sheet dsPIC33FJ64MC804
dsPIC33FJ32MC302/304, dsPIC33FJ64MCX02/X04, dsPIC33FJ128MCX02/X04 Family Errata dsPIC33FJ64MC804
16-bit MCU and DSC Programmer's Reference Manual PIC24FJ32GA002
dsPIC33F/PIC24H Flash Programming Specification dsPIC33FJ32GP204
AN1017 DM330023-2
AN1017 Source Code for MCHV-2 using dsPIC33EP256MC506 external OpAmp PIM DM330023-2
AN1017 Source Code for MCLV-2 using dsPIC33EP256MC506 external OpAmp PIM DM330023-2
AN1017 Source Code for dsPIC33EP512MU810 and dsPICDEM MCLV DM330023-2
AN1017 Source Code for dsPIC33EP512MU810 and dsPICDEM MCHV DM330023-2
AN1017 Source Code for dsPIC33FJ12MC202 DM330023-2
AN1017 Source Code for dsPIC33FJ256MC710 DM330023-2
AN1017 Source Code for dsPIC30F2010 DM330023-2
AN1017 Source Code for dsPIC33FJ32MC204 and dsPICDEM MCLV DM330023-2
AN1017 Source Code for dsPIC30F3010 DM330023-2
AN1044 dsPIC33FJ64MC804
AN1045 PIC24FJ32GA002
AN1069 PIC24FJ32GA002
Using C30 Compiler and the SPI Module to Interface EEPROMs with dsPIC33F PIC24FJ32GA002
AN1071 AC164124
IrDA Standard Stack for Microchip 16-bit Microcontrollers AC164124
IrDA Standard Stack for Microchip 32-bit Microcontrollers AC164124
AN1078 DM330021-2
AN1078 Tuning Guide DM330023-2
AN1078 Source Code for DV330100 using dsPIC33EV256GM106 DM330023-2
AN1078 Source Code for DV330100 using dsPIC33EP512GM710 DM330023-2
AN1078 Source Code for dsPIC33FJ32MC204 and dsPICDEM MCHV DM330023-2
AN1078 Source Code for dsPIC33FJ32MC204 and dsPICDEM MCLV DM330023-2
AN1078 Source Code for MCLV-2 using dsPIC33EP256MC506 External OpAmp PIM DM330023-2
AN1078 Source Code for dsPIC33EP512MU810 and dsPICDEM MCHV DM330023-2
AN1078 Source Code for dsPIC33EP512MU810 and dsPICDEM MCLV DM330023-2
AN1078 Source Code for MCHV-2 using dsPIC33EP256MC506 Internal OpAmp PIM DM330023-2
AN1078 Source Code for MCLV-2 using dsPIC33EP256MC506 Internal OpAmp PIM DM330023-2
AN1078 Source Code for dsPIC33EP64MC504 and dsPICDEM MCLV DM330023-2
AN1078 Source Code for dsPIC33EP512MU810 & dsPICDEM MCLV Dual Motor PIM DM330023-2
AN1078 Source Code for dsPIC33FJ12MC202 and dsPICDEM MCLV DM330023-2
AN1078 Source Code for dsPIC33FJ256MC710 and dsPICDEM MCLV DM330023-2
Source Code for Sensorless FOC for PMSM with PFC for dsPIC30F6010A DM330023-2
AN1078 Source Code for dsPIC30F6010A DM330023-2
AN1079 dsPIC33FJ64MC804
AN1079 Source Code dsPIC33FJ64MC804
AN1094 PIC24FJ32GA002
AN1094 Source Code PIC24FJ32GA002
AN1096 25AA02E64
Using the C30 Compiler to Interface SPI Serial EEPROMs with dsPIC33F Source Code 25AA02E64
AN1100 24VL024
Using the C30 Compiler to Interface Serial EEPROMs with dsPIC33F 24VL024
AN1106 dsPIC33FJ64MC802
AN1106 Source Code for dsPIC30F6010A dsPIC33FJ64MC802
AN1106 Source Code for dsPIC33FJ12MC202 dsPIC33FJ64MC802
AN1115 dsPIC33FJ64MC804
AN1115 Source Code dsPIC33FJ64MC804
AN1160 DM330023-2
Legacy dsPIC33F and dsPIC30F AN1160 App Note and Source Code DM330023-2
AN1160 Source Code for dsPIC33EP512MU810 and dsPICDEM MCHV DM330023-2
AN1160 Source Code for dsPIC33EP512MU810 and dsPICDEM MCLV DM330023-2
AN1160 Source Code for dsPIC33EP64MC504 using MCHV DM330023-2
AN1160 Source Code for dsPIC33EP64MC504 using MCLV DM330023-2
AN1160 Source Code for dsPIC33EP256MC506 using MCHV DM330023-2
AN1160 Source Code for dsPIC33EP256MC506 using MCLV DM330023-2
AN1162 DM330023-2
AN1162 Source Code for MCHV-2 using dsPIC33EP256MC506 External OpAmp PIM DM330023-2
AN1162 Source Code for MCHV-2 using dsPIC33EP256MC506 Internal OpAmp PIM DM330023-2
AN1162 Source Code for dsPIC33EP512MU810 and dsPICDEM MCHV DM330023-2
AN1162 Source Code for dsPIC33FJ32MC204 and dsPICDEM MCHV DM330023-2
AN1162 Source Code for dsPIC30F6010A DM330023-2
AN1162 Source Code for dsPIC33FJ256MC710 DM330023-2
AN1204 PIC24FJ32GA002
AN1206 DM330023-2
AN1206 Source Code for dsPIC30F6010A DM330023-2
AN1206 Source Code for dsPIC33FJ12MC202 DM330023-2
AN1206 Source Code for dsPIC33FJ256MC710 DM330023-2
AN1208 DM330023-2
AN1208 Source Code for dsPIC30F6010A DM330023-2
AN1208 Source Code DM330023-2
AN1210 dsPIC33FJ64MC804
AN1210 Source Code dsPIC33FJ64MC804
AN1227 PIC24FJ32GA002
AN1229 ENC28J60
PIC18F ClassB-2 Library_Feb2012.zip ENC28J60
AN1236 PIC24FJ16GA002
AN1236 Source Code PIC24FJ16GA002
ECAN? Operation with DMA on dsPIC33F and PIC24H Devices dsPIC33FJ64MC804
AN1292 DM330023-2
AN1292 Source Code for DV330100 using dsPIC33EV256GM106 DM330023-2
AN1292 Source Code for DV330100 using dsPIC33EP512GM710 DM330023-2
AN1292 Source Code for dsPIC33EP512MU810 and dsPICDEM MCLV DM330023-2
AN1292 Source Code for dsPIC33EP512MU810 and dsPICDEM MCHV DM330023-2
AN1292 Source Code for MCLV-2 using dsPIC33EP256MC506 External OpAmp PIM DM330023-2
AN1292 Source Code for MCLV-2 using dsPIC33EP256MC506 Internal OpAmp PIM DM330023-2
AN1292 Source Code for MCHV-2 using dsPIC33EP256MC506 External OpAmp PIM DM330023-2
AN1292 Source Code for MCHV-2 using dsPIC33EP256MC506 Internal OpAmp PIM DM330023-2
AN1292 Source Code for dsPIC33EP64MC504 and dsPICDEM MCLV DM330023-2
AN1292 Source Code for dsPIC33FJ32MC204 and dsPICDEM MCLV DM330023-2
AN1299 dsPIC33EP64MC504
AN1299 Source Code for dsPIC33EP512MU810 and dsPICDEM MCHV dsPIC33EP64MC504
AN1299 Source Code for dsPIC33EP512MU810 and dsPICDEM MCLV dsPIC33EP64MC504
AN1299 Source Code for dsPIC33FJ32MC204 and dsPICDEM MCLV dsPIC33EP64MC504
AN1299 Source Code for dsPIC33FJ32MC204 and dsPICDEM MCHV dsPIC33EP64MC504
AN1307 DM330022
AN1307 Source Code for dsPIC33EP512MU810 and dsPICDEM MCSM DM330022
AN1307 Source Code for dsPIC33FJ32MC204 and dsPICDEM MCSM DM330022
AN699 MCP3021
AN887 dsPIC33FJ64MC802
AN901 dsPIC33FJ64MC706A
SWAN0901 Source Code for dsPIC 28-pin devices and the PICDEM MCLV Board dsPIC33FJ64MC706A
SWAN0901 Source Code dsPIC33FJ64MC706A
SWAN0901 Source Code for the dsPIC33FJ256MC710 dsPIC33FJ64MC706A
AN908 DM330023-2
AN908 Source Code DM330023-2
AN908 Source Code for dsPIC30F6010A DM330023-2
AN908 Source Code for dsPIC33FJ12MC202 DM330023-2
AN957 DM330023-2
AN957 Source Code for dsPIC30F2010 DM330023-2
AN957 Source Code for dsPIC33FJ12MC202 DM330023-2
AN957 Source Code for dsPIC33FJ32MC204 and dsPICDEM MCLV DM330023-2
AN957 Source Code for dsPIC33FJ256MC710 DM330023-2
AN984 dsPIC33FJ64MC802
AN984 Source Code for dsPIC30F6010A dsPIC33FJ64MC802
AN984 Source Code for dsPIC33FJ12MC202 dsPIC33FJ64MC802
AN984 Source Code for dsPIC33FJ256MC710 dsPIC33FJ64MC802
AN992 dsPIC33FJ64MC804
SWAN0992 Source Code dsPIC33FJ64MC804
16-bit Embedded Control Solutions Brochure PIC24FJ32GA002
Electronic Solutions for Medical and Fitness 24VL025
Motor Control and Drive Brochure dsPIC33EP64MC504
MPLAB® X IDE Product Overview 24VL025
dsPIC33/PIC24 FRM, I2C PIC24FJ32GA002
dsPIC33/PIC24 FRM, Output Compare PIC24FJ32GA002
dsPIC33/PIC24 FRM, Serial Peripheral Interface (SPI) PIC24FJ32GA002
dsPIC33/PIC24 FRM, UART PIC24FJ32GA002
Section 02. CPU - dsPIC33F FRM dsPIC33FJ32GP204
Section 03. Data Memory - dsPIC33F/PIC24H FRM dsPIC33FJ32GP204
Section 04. Program Memory - dsPIC33F/PIC24H FRM dsPIC33FJ32GP204
Section 05. Flash Programming - dsPIC33F/PIC24H FRM dsPIC33FJ32GP204
Section 08. Reset - dsPIC33F FRM dsPIC33FJ32GP204
Section 10. I/O Ports - dsPIC33F/PIC24H FRM dsPIC33FJ32GP204
Section 11. Timers - dsPIC33F/PIC24H FRM dsPIC33FJ32GP204
Section 12. Input Capture - dsPIC33F FRM dsPIC33FJ32GP204
Section 14. Motor Control PWM - dsPIC33F/PIC24H FRM dsPIC33FJ64MC804
Section 15. Quadrature Encoder Interface (QEI) - dsPIC33F FRM dsPIC33FJ64MC804
Section 16. Analog-to-Digital Converter (ADC) - dsPIC33F/PIC24H FRM dsPIC33FJ32GP204
Section 21. Enhanced Controller Area Network (ECAN) - dsPIC33F/PIC24H FRM dsPIC33FJ64MC804
Section 23. CodeGuard Security - dsPIC33F/PIC24H FRM dsPIC33FJ32GP204
Section 24. Programming and Diagnostics - dsPIC33F/PIC24H FRM dsPIC33FJ32GP204
Section 25. Device Configuration - dsPIC33F/PIC24H FRM dsPIC33FJ32GP204
Section 26. Development Tool Support - dsPIC33F FRM dsPIC33FJ32GP204
Section 30. I/O Ports with Peripheral Pin Select (PPS) - dsPIC33F/PIC24H FRM dsPIC33FJ32GP204
Section 31. Introduction (Part III) - dsPIC33F FRM dsPIC33FJ64MC804
Section 32. Interrupts (Part III) - dsPIC33F/PIC24H FRM dsPIC33FJ64MC804
Section 33. Audio Digital-to-Analog Converter (DAC) - dsPIC33F FRM dsPIC33FJ64MC804
Section 34. Comparator - dsPIC33F FRM dsPIC33FJ64MC804
Section 35. Parallel Master Port (PMP) - dsPIC33F/PIC24H FRM dsPIC33FJ64MC804
Section 36. Programmable Cyclic Redundancy Check (CRC) - dsPIC33F FRM dsPIC33FJ64MC804
Section 37. Real-Time Clock and Calendar (RTCC) - dsPIC33F/PIC24H FRM dsPIC33FJ64MC804
Section 38. Direct Memory Access (DMA) (Part III) - dsPIC33F/PIC24H FRM dsPIC33FJ64MC804
Section 39. Oscillator (Part III) - dsPIC33F FRM dsPIC33FJ64MC804
Program Executive RIPE_01b_000033 PIC24FJ32GA002
dsPICDEM MCSM Development Board Demonstration Software dsPIC33FJ12GP202
CE100 - Using A/D Converters and DSP Library for Signal Filtering dsPIC33FJ32GP204
CE101 - Configuring 10-bit A/D Converters for 1MSPS Conversion Rate dsPIC33FJ32GP204
CE102 - Performing A/D Conversions in SLEEP (Low-Power) Mode dsPIC33FJ32GP204
CE103 - Implementing DOZE Mode for Dynamic CPU Power Control dsPIC33FJ32GP204
CE104 - Dynamic Clock Switching for Low Power Operation dsPIC33FJ32GP204
CE105 - Address Error Traps for Easy Debugging dsPIC33FJ32GP204
CE106 - Math Error Traps for Robust Operation dsPIC33FJ32GP204
CE107 - Stack Error Traps for Easy Debugging dsPIC33FJ32GP204
CE108 - Oscillator Failure Traps and Failsafe Clock Monitoring dsPIC33FJ32GP204
CE109 - Run-Time Self Programming of FLASH Program Memory dsPIC33FJ32GP204
CE110 - Dynamic Tuning of Internal Fast RC dsPIC33FJ32GP204
CE111 - External Interrupt Pins Configuration and Use dsPIC33FJ32GP204
CE112 - Fast Wake-up From Sleep Mode dsPIC33FJ32GP204
CE113 - Timer1 used in Real-Time Clock Applications dsPIC33FJ32GP204
CE114 - Using the DMA with the UART in Loopback mode dsPIC33FJ32GP204
CE115 - Example of Handling a DMA Trap dsPIC33FJ32GP204
CE116 - Using the DMA with the SPI module dsPIC33FJ32GP204
CE117 - Using the DMA with DCI peripheral for I2S driver dsPIC33FJ32GP204
CE118 - Using FIR Filters From dsPIC Filter Design and DSP Library dsPIC33FJ32GP204
CE119 Interfacing to I2C Serial EEPROM using I2C peripheral dsPIC33FJ32GP204
CE120 A/D Conversions with Scanning through selected Analog Inputs with DMA dsPIC33FJ32GP204
CE121 A/D Conversions with Scanning through selected Analog Inputs without DMA dsPIC33FJ32GP204
CE122 - ADC Alternate Sampling dsPIC33FJ32GP204
CE123 - CodeGuard(TM) Security: segment creation and code placement dsPIC33FJ32GP204
CE124 - CodeGuard(TM) Security: Program flow changes between segments dsPIC33FJ32GP204
CE127 - Crosswire Communication between ECAN 1 and ECAN 2 modules dsPIC33FJ32GP204
CE128 - ECAN FIFO Receive Example dsPIC33FJ32GP204
CE129 - ECAN Remote Transmission Request dsPIC33FJ32GP204
CE135 - SPI Demo dsPIC33FJ32GP204
CE136 - SPI without DMA dsPIC33FJ32GP204
CE137 - UART without DMA dsPIC33FJ32GP204
CE138 - SPI with two slaves dsPIC33FJ32GP204
CE139 - 10-bit ADC Sampling at 2.2MSPS dsPIC33FJ32GP204
CE140 - Inverse tangent operation using CORDIC iterative approximation dsPIC33FJ32GP204
CE141 - SPI with Framed mode dsPIC33FJ32GP204
CE142 - Open Drain configuration dsPIC33FJ32GP204
CE143 - Using Timer1 for Period Interrupts dsPIC33FJ32GP204
CE145 - Using I2C module as a Slave device dsPIC33FJ32GP204
CE146 - Adaptive Notch Filter dsPIC33FJ32GP204
CE147 - Signal Matching using Coherence Function Cross Spectral Density dsPIC33FJ32GP204
CE148 - ADC Sampling with DMA and FIR Filtering - Apps include Circuit Breakers dsPIC33FJ32GP204
CE149 - Signal generation, fractional sampling rate, interpolation, decimation dsPIC33FJ32GP204
CE150 - JPEG Entropy Coding dsPIC33FJ32GP204
CE151 - CRC Generation dsPIC33FJ32GP204
CE152 - Parallel Master Port (PMP) Example dsPIC33FJ32GP204
CE153 - RTCC dsPIC33FJ32GP204
CE154 - ADC to DAC Loopback dsPIC33FJ32GP204
CE155 - Real-Time Data Monitoring (RTDM) Example dsPIC33FJ32GP204
Download Recorded Presentation File (slides + audio): dsPIC33FJ32GP204
Download Presentation File(slides + text) in .pdf format: dsPIC33FJ32GP204
dsPICDEM MCHV Development System Users Guide DM330023-2
CE125 - CodeGuard(TM) Security: Secure Segment Erase dsPIC33FJ32GP204
CE144 - CodeGuard Application Example dsPIC33FJ32GP204
dsPIC33FJ128GP804 and PIC24HJ128GP504 PIM Information Sheet for Graphics Apps dsPIC33FJ64MC804
dsPIC33FJ128MC804 PIM Information Sheet AC164128
In-Circuit Debugging Interface Options with dsPIC DSC PIC24FJ32GA002