STEVAL-IFP015V2:ISO8200B High Side Driver - 8 Channels evaluation board

The STEVAL-IFP015V2 demonstration board works in combination with the STEVAL-PCC009V2 or STEVAL-PCC009V1 interface board to allow evaluation of all the features of the ISO8200B device. A large GND area on the printed circuit board has been designed to minimize noise effects and ensure good thermal performance.

The ISO8200B is a galvanic isolated 8 channel driver featuring a very low supply current. It contains 2 independent galvanic isolated voltage domains (VCC for the power stage and VDD for the digital stage). The IC is intended to drive any type of load with one side connected to ground. Active channel current limitation combined with thermal shutdown, independent for each channel, and automatic restart protect the device against overload. Additional embedded functions are: loss of GND protection which automatically turns off the outputs in case of analog ground, undervoltage shutdown with hysteresis, and reset function for immediate power output shutdown.

Built-in thermal shutdown protects the chip against overtemperature and short-circuit. In overload condition, the channel turns off, then back on automatically after the IC temperature has decreased below a reset threshold. If this condition causes the case temperature to reach the TCR limit, the overloaded channel is turned off and will restart only when case and junction temperature have decreased down to the reset threshold. Non overloaded channels continue to operate normally.

An internal circuit provides an OR-wired non latched common FAULT indicator signaling channel OVT. The FAULT pin is an open-drain active-low fault indication pin.

Key Features

  • VCC operating voltage from 10.5 to 33 V
  • 0.7 A for each channel
  • Reverse polarity protection on VCC and VDD supply voltage
  • Digital supply voltage VDD 3.3/5 V
  • Microcontroller interface direct/synchronous mode communication
  • Designed to meet requirements of IEC 61000-4-2, IEC 61000-4-4, IEC 61000-4-5 standards
  • RoHS compliant
产品规格
DescriptionVersionSize
DB2037: Galvanically-isolated 8 channel high-side driver based on the ISO8200B1.0160 KB
应用手册
DescriptionVersionSize
AN4373: Galvanically-isolated 8 channel high-side driver based on the ISO8200B1.01 MB
Board Manufacturing Specifications
DescriptionVersionSize
STEVAL-IFP015V2 gerber files1.0690 KB
Bill of Materials
DescriptionVersionSize
STEVAL-IFP015V2 BOM1.09 KB
Schematic Packs
DescriptionVersionSize
STEVAL-IFP015V2 schematics1.0121 KB
手册
DescriptionVersionSize
Products and Solutions for Factory Automation and Control1.03 MB
许可协议
DescriptionVersionSize
Evaluation products license agreement1.0125 KB
Evaluation Tool Software
型号制造商Description
STSW-IFP015STSW-IFP015 application software setup
样片和购买
型号Core ProductUnit Price (US$) *QuantityECCN (EU)ECCN (US)Country of Origin
STEVAL-IFP015V2ISO8200B72.281NECEAR99ITALY
质量和可靠性
型号PackageGradeRoHS Compliance GradeMaterial Declaration**
STEVAL-IFP015V2CARDIndustrialEcopack2
Galvanically-isolated 8 channel high-side driver based on the ISO8200B STEVAL-IFP015V2
Galvanically-isolated 8 channel high-side driver based on the ISO8200B STEVAL-IFP015V2
Galvanically-isolated 8 channel high-side driver based on the ISO8200B STEVAL-IFP015V2
Galvanically-isolated 8 channel high-side driver based on the ISO8200B STEVAL-IFP015V2
Galvanically-isolated 8 channel high-side driver based on the ISO8200B STEVAL-IFP015V2
STEVAL-SPIMD20V1 demonstration kit based on the SPIMD20 integrated motor drive STEVAL-SPIMD20V1
ST-LINK/V2 in-circuit debugger/programmer for STM8 and STM32 ST-LINK-V2