STEVAL-ISB033V1:Evaluation board for STBCFG01 single-cell Li+ battery charger with OTG boost, voltage mode fuel gauge and 200 mA LDO

The STEVAL-ISB033V1 is an evaluation board to test the first-of-its-kind STBCFG01 switch mode battery charger for single cell Li-Ion batteries, which integrates a highly accurate voltage mode fuel gauge to monitor a battery's state of charge. The device also provides a 5 V output to supply USB OTG (on-the-go) bus-powered devices in addition to an LDO linear voltage regulator to support system boot in dead battery conditions.

The STBCFG01 uses accurate measurements of the battery voltage which allows the estimation of the battery's state-of-charge (SOC) without a current-sensing resistor. The switching charger works together with the fuel gauge to simplify monitoring features and to save current consumption when the device is not charging. The battery charger features a smart input current limit; the maximum input current can be selected through the I²C interface, and if the input voltage drops below a programmable threshold, even if the selected maximum current limit current has not been reached yet the dynamic input current limit function is activated, preventing the input current from increasing further. The dynamic input current limit function can be disabled, if necessary. An automatic input pre-bias load makes the device suitable for applications using voltage sources requiring a minimum external load for correct regulation.

Key Features

    • 2 MHz or 3 MHz switching frequency
    • 1.2 A max. charging current
    • 20 V tolerant input with OVP
    • Programmable input current limitation and dynamic input current limit
    • Battery overvoltage protection
    • Auto-recharge
    • Integrated current sensing resistor
    • USB compatible
  • Voltage mode fuel gauge
    • External sensing resistor not needed
    • Battery swap detection through ID resistor
    • Low battery voltage and low SOC programmable alarms
  • 50 mA LDO for system boot in dead battery condition
  • USB OTG VBUS generation (500 mA)
    • USB overvoltage protection
    • Programmable battery overcurrent protection
  • Automatic 60 mA input pre-bias
  • I²C compatible control interface
  • Interrupt output pin
  • RoHS compliant
产品规格
DescriptionVersionSize
DB2572: Evaluation board for STBCFG01 single-cell Li+ battery charger with OTG boost, voltage mode fuel gauge and 200 mA LDO1.0325 KB
用户手册
DescriptionVersionSize
UM1993: Switch mode single cell Li+ battery charger with OTG boost, voltage mode fuel gauge and LDO1.02 MB
Board Manufacturing Specifications
DescriptionVersionSize
STEVAL-ISB033V1 gerber files1.0375 KB
Bill of Materials
DescriptionVersionSize
STEVAL-ISB033V1 BOM1.075 KB
Schematic Packs
DescriptionVersionSize
STEVAL-ISB033V1 schematic1.0155 KB
许可协议
DescriptionVersionSize
Evaluation products license agreement1.0125 KB
样片和购买
型号Core ProductUnit Price (US$) *QuantityECCN (EU)ECCN (US)Country of Origin
STEVAL-ISB033V1STBCFG0153.901NECEAR99ITALY
质量和可靠性
型号PackageGradeRoHS Compliance GradeMaterial Declaration**
STEVAL-ISB033V1CARDIndustrialEcopack2
Evaluation board for STBCFG01 single-cell Li+ battery charger with OTG boost, voltage mode fuel gauge and 200 mA LDO STEVAL-ISB033V1
Switch mode single cell Li+ battery charger with OTG boost, voltage mode fuel gauge and LDO STEVAL-ISB033V1
Switch mode single cell Li+ battery charger with OTG boost, voltage mode fuel gauge and LDO STEVAL-ISB033V1
Switch mode single cell Li+ battery charger with OTG boost, voltage mode fuel gauge and LDO STEVAL-ISB033V1
Switch mode single cell Li+ battery charger with OTG boost, voltage mode fuel gauge and LDO STEVAL-ISB033V1
ST-LINK/V2 in-circuit debugger/programmer for STM8 and STM32 ST-LINK-V2