Home > Littelfuse > Battery Management > FlexMod Electronic Modules > FlexMod Voltage Sensing Relays & Timers

FlexMod Voltage Sensing Relays & Timers Series - Senses Voltage and Time While Vehicle is Off to Disconnect Auxiliary Loads

DataSheet:Download FlexMod Voltage Sensing Datasheet

The FlexMod electronic voltage sensing relay & timer monitors both battery voltage and ignition status, shutting down non-critical loads when the cutoff voltage is reached, or at the set time after the ignition is turned off. It is a timer and voltage sensor in one easy-to- connect unit. Ideal for use in emergency vehicles, the unit senses both voltage and time; after the vehicle engine is turned off, if  either the cutoff voltage or time limit is reached, the Voltage Sensing Relay & Timer FlexMod will shut down the auxiliary loads. The dual technology in package provides double protection. Features & Benefits FlexMod Dual Output Voltage Sensing Relay & Timer 48742 - Controls two outputs, monitors voltage and time on both. Protects starting battery from being drained by auxiliary loads and protects battery voltage two ways. Dual output unit (controls two circuits) permits prioritization of load-shedding. Monitors voltage and time simultaneously, providing double the protection to batteries. Battery will not be drained if battery voltage gets low before timer has run out. Unit can be used as-is, with factory-programmed presets, or can be programmed by dealers to a broad scale of values. Ordering Information Part Number Description Harness Included Programmable 48541 Unit Only 48541-01 Unit with Harness • 48741 Programmable Unit Only • 48742 Dual Output Programmable Unit Only •

• Compact design (4” x 3” x 1”) unit is waterproof, dustproof and vibration-proof.  Mounts anywhere on a vehicle, even places where road-splash is a problem. Sealed to IP67 standard.
• Preserves starting power; eliminates downtime and jump starts due to dead batteries. Simultaneous time and voltage sensing protects starting, even when the vehicle is running "in deficit".
• Monitors voltage and time simultaneously, providing double the protection to batteries. Battery will not be  drained if battery voltage gets low before timer has run out.
• 10A rating means it can handle many loads directly or drive a relay or solenoid for higher amperage
• Unit is autoranging - senses 12 Vdc or 24 Vdc systems.

Ordering Information

Catalog #	Connector	Description	Dimensions	Disconnect voltage (12V)	Disconnect voltage (24V)	Humidity	Inductive transient	Ingress Protection	Load current	Load dump
48541	8-pin Sealed Deutsch type	Voltage Sensing Relay and Timer Unit	4 x 2.7 x 1.31	12.05 V min12.1 V typical12.15 V max	24.1 V min24.2 V typical24.3 V max	0 to 90% RH	+/- 600 V	IP67	10 A at 85C	+ 150 V
48541-01	8-pin Sealed Deutsch type	Voltage Sensing Relay and Timer with 12805 Harness	4 x 2.7 x 1.31	12.05 V min12.1 V typical12.15 V max	24.1 V min24.2 V typical24.3 V max	0 to 90% RH	+/- 600 V	IP67	10 A at 85C	+ 150 V
48741	8-pin Sealed Deutsch type	Programmable Voltage Sensing Relay and Timer	4 x 2.7 x 1.31	Programmable Attribute	Programmable Attribute	0 to 90% RH	+/- 600 V	IP67	10 A at 85C	+ 150 V
48742	8-pin Sealed Deutsch type	Dual Output Voltage Sensing Relay and Timer Unit	4 x 2.7 x 1.31	Output 1 - 11.5 Vdc / Output 2 - 12.1 Vdc	Output 1 - 23.0 Vdc / Output 2 24.2 Vdc	0 to 90% RH	+/- 600 V	IP67		+ 150 V

Resources

• 48541 - FlexMod™ Voltage Sensing Relay & Timer Info Sheet
• 48742 - FlexMod™ Dual Output Voltage Sensing Relay & Timer Info Sheet
• 48541 & 48741 - Voltage Sensing Relay Timer 2D Prints
• 48742 - Dual Output Voltage Sensing Relay Timer 2D Print