• 简体中文
• English

MAX19517：Dual-Channel, 10-Bit, 130Msps ADC

10-Bit, 130Msps Dual ADC Provides 60dBFS SNR and 85dBFS SFDR at 75mW per Channel

The MAX19517 dual-channel, analog-to-digital converter (ADC) provides 10-bit resolution and a maximum sample rate of 130Msps. The MAX19517 analog input accepts a wide 0.4V to 1.4V input common-mode voltage range, allowing DC-coupled inputs for a wide range of RF, IF, and baseband front-end components. The MAX19517 provides excellent dynamic performance from baseband to high input frequencies beyond 400MHz, making the device ideal for zero-intermediate frequency (ZIF) and high-intermediate frequency (IF) sampling applications. The typical signal-to-noise ratio (SNR) performance is 59.8dBFS and typical spurious-free dynamic range (SFDR) is 82dBc at fIN = 70MHz and fCLK = 130MHz. The MAX19517 operates from a 1.8V supply. Additionally, an integrated, self-sensing voltage regulator allows operation from a 2.5V to 3.3V supply (AVDD). The digital output drivers operate on an independent supply voltage (OVDD) over the 1.8V to 3.5V range. The analog power consumption is only 74mW per channel at VAVDD = 1.8V. In addition to low operating power, the MAX19517 consumes only 1mW in power-down mode and 21mW in standby mode. Various adjustments and feature selections are available through programmable registers that are accessed through the 3-wire serial-port interface. Alternatively, the serial-port interface can be disabled, with the three pins available to select output mode, data format, and clock-divider mode. Data outputs are available through a dual parallel CMOS-compatible output data bus that can also be configured as a single multiplexed parallel CMOS bus. The MAX19517 is available in a small 7mm x 7mm 48-pin thin QFN package and is specified over the -40°C to +85°C extended temperature range. Refer to the MAX19505, MAX19506, and MAX19507 data sheets for pin- and feature-compatible 8-bit, 65Msps, 100Msps, and 130Msps versions, respectively. Refer to the MAX19515 and MAX19516 data sheets for pin- and feature-compatible 10-bit, 65Msps and 100Msps versions, respectively.

Key Features Very-Low-Power Operation (74mW/Channel at 130Msps) 1.8V or 2.5V to 3.3V Analog Supply Excellent Dynamic Performance 59.8dBFS SNR at 70MHz 82dBc SFDR at 70MHz User-Programmable Adjustments and Feature Selection through an SPI™ Interface Selectable Data Bus (Dual CMOS or Single Multiplexed CMOS) DCLK Output and Programmable Data Output Timing Simplifies High-Speed Digital Interface Very Wide Input Common-Mode Voltage Range (0.4V to 1.4V) Very High Analog Input Bandwidth (> 850MHz) Single-Ended or Differential Analog Inputs Single-Ended or Differential Clock Input Divide-by-One (DIV1), Divide-by-Two (DIV2), and Divide-by-Four (DIV4) Clock Modes Two's Complement, Gray Code, and Offset Binary Output Data Format Out-of-Range Indicator (DOR) CMOS Output Internal Termination Options (Programmable) Reversible Bit Order (Programmable) Data Output Test Patterns Small 7mm x 7mm 48-Pin Thin QFN Package with Exposed Pad

MAX19517: Functional Diagram Applications/Uses Digital Set-Top Boxes IF and Baseband Communications, Including Cellular Base Stations and Point-to-Point Microwave Receivers Portable Instrumentation and Low-Power Data Acquisition Ultrasound and Medical Imaging

DataSheet

Parametrics

Design kits & evaluation modules

• MAX19505EVKIT
• MAX19506EVKIT
• MAX19507EVKIT
• MAX19515EVKIT
• MAX19516EVKIT
• MAX19517EVKIT

Quality and Environmental Data

• MAX19517.pdf

Ordering Information