技术参数

Emulators & Debuggers

• PICkit 3 In-Circuit Debugger (PG164130)
• MPLAB ICD 3 In-Circuit Debugger (DV164035)
• MPLAB REAL ICE PROBE KIT (DV244005)
• MPLAB ICD 2 MODULE (DV164005)
• PICkit 2 Microcontroller Programmer (PG164120)

Demo & Eval Boards

• PICtail Daughter Board for SD & MMC Cards (AC164122)
• IrDA PICtail Plus Daughter Board (AC164124)
• PICkit 2 Debug Express (DV164121)
• Microstick for dsPIC33F and PIC24H (DM330013)
• Ethernet PICtail Plus Daughter Board (AC164123)
• PIC24H CVD Capacitive Touch Eval Board (AC243026)
• Explorer 16 Development Board (100-pin) (DM240001)
• MPLAB Starter Kit for PIC24H (DM240021)
• Microstick II (DM330013-2)
• Speech Playback PICtail Plus Daughter Board (AC164125)
• AUDIO PICTAIL PLUS DAUGHTER BOARD (AC164129)

Programmer

• MPLAB PM3 Universal Device Programmer (DV007004)
• MPLAB ICD 3 In-Circuit Debugger (DV164035)
• PICkit 3 In-Circuit Debugger (PG164130)
• MPLAB REAL ICE PROBE KIT (DV244005)
• MPLAB ICD 2 MODULE (DV164005)
• PICkit 2 Microcontroller Programmer (PG164120)

Software & Compilers

• Gimpel Software PC-lint Workstation License (SW500060)

技术特性

• Up to 40 MIPS operation (@ 3.0-3.6V):- Industrial temperature range (-40°C to +85°C)- Extended temperature range (-40°C to +125°C)- High temperature range (-40°C to +150°C)High-Performance CPU:
• Modified Harvard architecture
• C compiler optimized instruction set
• 16-bit wide data path
• 24-bit wide instructions
• Linear program memory addressing up to 4M instruction words
• Linear data memory addressing up to 64 Kbytes
• 71 base instructions, mostly 1 word/1 cycle
• Sixteen 16-bit General Purpose Registers
• Flexible and powerful addressing modes
• Software stack
• 16 x 16 multiply operations
• 32/16 and 16/16 divide operations
• Up to ±16-bit shifts for up to 40-bit dataInterrupt Controller:
• 5-cycle latency
• 118 interrupt vectors
• Up to 21 available interrupt sources
• Up to 3 external interrupts
• 7 programmable priority levels
• 4 processor exceptionsOn-Chip Flash and SRAM:
• Flash program memory (up to 32 Kbytes)
• Data SRAM (2 Kbytes)
• Boot and General Security for Program FlashDigital I/O:
• Peripheral Pin Select Functionality
• Up to 35 programmable digital I/O pins
• Wake-up/Interrupt-on-Change for up to 21 pins
• Output pins can drive from 3.0V to 3.6V
• Up to 5V output with open drain configuration
• All digital input pins are 5V tolerant
• 4 mA sink on all I/O pinsSystem Management:
• Flexible clock options:- External, crystal, resonator, internal RC- Fully integrated Phase-Locked Loop (PLL)- Extremely low jitter PLL
• Power-up Timer
• Oscillator Start-up Timer/Stabilizer
• Watchdog Timer with its own RC oscillator
• Fail-Safe Clock Monitor
• Reset by multiple sourcesPower Management:
• On-chip 2.5V voltage regulator
• Switch between clock sources in real time
• Idle, Sleep and Doze modes with fast wake-upTimers/Capture/Compare:
• Timer/Counters, up to three 16-bit timers:- Can pair up to make one 32-bit timer- 1 timer runs as Real-Time Clock with external32.768 kHz oscillator- Programmable prescaler
• Input Capture (up to 4 channels):- Capture on up, down or both edges- 16-bit capture input functions- 4-deep FIFO on each capture
• Output Compare (up to 2 channels):- Single or Dual 16-Bit Compare mode- 16-bit Glitchless PWM ModeCommunication Modules:
• 4-wire SPI- Framing supports I/O interface to simple codecs- Supports 8-bit and 16-bit data- Supports all serial clock formats and sampling modes
• I2C™- Full Multi-Master Slave mode support- 7-bit and 10-bit addressing- Bus collision detection and arbitration- Integrated signal conditioning- Slave address masking
• UART- Interrupt on address bit detect- Interrupt on UART error- Wake-up on Start bit from Sleep mode- 4-character TX and RX FIFO buffers- LIN bus support- IrDA® encoding and decoding in hardware- High-Speed Baud mode- Hardware Flow Control with CTS and RTSAnalog-to-Digital Converters (ADCs):
• 10-bit, 1.1 Msps or 12-bit, 500 Ksps conversion:- 2 and 4 simultaneous samples (10-bit ADC)- Up to 10 input channels with auto-scanning- Conversion start can be manual or synchronized with 1 of 4 trigger sources- Conversion possible in Sleep mode- ±2 LSb max integral nonlinearity- ±1 LSb max differential nonlinearityCMOS Flash Technology:
• Low-power, high-speed Flash technology
• Fully static design
• 3.3V (±10%) operating voltage
• Industrial and extended temperature
• Low-power consumptionPackaging:
• 28-pin SDIP/SOIC/QFN-S