• 简体中文
• English

MAX6965：9-Output LED Driver with Intensity Control and Hot-Insertion Protection

9-Output LED Driver with Intensity Control and Hot-Insertion Protection has 240-Step Brightness Control and 2-Phase Blink

The MAX6965 I²C-compatible serial interfaced peripheral provides microprocessors with nine additional output ports. Each output is an open-drain current-sinking output rated to 50mA at 7V. All outputs are capable of driving LEDs, or providing logic outputs with external resistive pullup up to 7V. Eight-bit PWM current control is also integrated. Four of the bits are global control and apply to all LED outputs to provide coarse adjustment of current from fully off to fully on with 14 intensity steps. Additionally each output then has an individual 4-bit control, which further divides the globally set current into 16 more steps. Alternatively, the current control can be configured as a single 8-bit control that sets all outputs at once. Each output has independent blink timing with two blink phases. LEDs can be individually set to be either on or off during either blink phase, or to ignore the blink control. The blink period is controlled by an external clock (up to 1kHz) on BLINK or by a register. The BLINK input can also be used as a logic control to turn the LEDs on and off, or as a general-purpose input (GPI). The MAX6965 supports hot insertion. The SDA, SCL, active-low RST, BLINK, and the slave address input AD0 remain high impedance in power-down (V+ = 0V) with up to 6V asserted upon them. The output ports remain high impedance with up to 8V asserted upon them. The MAX6965 is controlled through a 2-wire I²C serial interface, and can be configured to one of four I²C addresses.

Key Features 400kbps, 2-Wire Serial Interface, 5.5V Tolerant 2V to 3.6V Operation Overall 8-Bit PWM LED Intensity Control Global 16-Step Intensity Control Plus Individual 16-Step Intensity Controls Two-Phase LED Blinking High Port Output Current—Each Port 50mA (max) Active-Low RST Input Clears Serial Interface and Restores Power-Up Default State Supports Hot Insertion Outputs are 7V-Rated Open Drain Low Standby Current (1.2µA (typ), 3.3µA (max)) Tiny 3mm x 3mm, Thin QFN Package -40°C to +125°C Temperature Range

MAX6965: Typical Application Circuit Applications/Uses Keypad Backlights LCD Backlights LED Status Indication RGB LED Drivers

DataSheet

Parametrics

Design kits & evaluation modules

• MAX6965EVCMAXQU
• MAX6965EVKIT

Quality and Environmental Data

• MAX6965.pdf

Related Products

• MAX7318：2-Wire-Interfaced, 16-Bit, I/O Port Expander with Interrupt and Hot-Insertion Protection
• MAX7317：10-Port SPI-Interfaced I/O Expander with Overvoltage and Hot-Insertion Protection
• MAX6964：17-Output LED Driver/GPO with Intensity Control and Hot-Insertion Protection
• MAX7314：18-Port GPIO with LED Intensity Control, Interrupt, and Hot-Insertion Protection
• MAX7316：10-Port I/O Expander with LED Intensity Control, Interrupt, and Hot-Insertion Protection
• MAX7315：8-Port I/O Expander with LED Intensity Control, Interrupt, and Hot-Insertion Protection
• MAX7313：16-Port I/O Expander with LED Intensity Control, Interrupt, and Hot-Insertion Protection
• MAX7312：2-Wire-Interfaced 16-Bit I/O Port Expander with Interrupt and Hot-Insertion Protection
• MAX6965：9-Output LED Driver with Intensity Control and Hot-Insertion Protection
• MAX7311：2-Wire-Interfaced 16-Bit I/O Port Expander with Interrupt and Hot-Insertion Protection
• MAX7310：2-Wire-Interfaced 8-Bit I/O Port Expander with Reset
• MAX7300：2-Wire-Interfaced, 2.5V to 5.5V, 20-Port or 28-Port I/O Expander
• MAX6956：2-Wire-Interfaced, 2.5V to 5.5V, 20-Port or 28-Port LED Display Driver and I/O Expander
• MAX7301：4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and 28-Port I/O Expander
• MAX6957：4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and 28-Port LED Display Driver and I/O Expander

Ordering Information