• 简体中文
• English

MAX7312：2-Wire-Interfaced 16-Bit I/O Port Expander with Interrupt and Hot-Insertion Protection

The MAX7312 2-wire-interfaced expander provides 16-bit parallel input/output (I/O) port expansion in SMBus™ and I²C applications. The MAX7312 consists of input port registers, output port registers, polarity inversion registers, configuration registers, a bus timeout register, and an I²C-compatible serial interface logic, compatible with SMBus. The system master can invert the MAX7312 input data by writing to the active-high polarity inversion register. The system master can enable or disable bus timeout by writing to the bus timeout register. Any of the 16 I/O ports can be configured as an input or an output. A power-on reset (POR) initializes the 16 I/Os as inputs. Three address select pins configure the part to one of 64 slave ID addresses. The MAX7312 supports hot insertion. All port pins, the active-low INT output, SDA, SCL, and the slave address inputs AD0-2 remain high impedance in power-down (Vt = 0V) up to 6V. The MAX7312 is available in 24-pin SO, SSOP, TSSOP, and thin QFN packages and is specified over the -40°C to +125°C automotive temperature range. For applications requiring I/Os with integrated 100kΩ pullup resistors, refer to the MAX7311 data sheet.

Key Features 400kbps I²C-Compatible Serial Interface 2V to 5.5V Operation 5V Overvoltage Tolerant I/Os Supports Hot Insertion 16 I/O Pins that Default to Inputs on Power-Up Open-Drain Interrupt Output (Active-Low INT) Bus Timeout for Lock-Up-Free Operation Noise Filter on SCL/SDA Inputs 64 User-Selectable Slave ID Addresses Low Standby Current (2.9µA typ) Polarity Inversion 4mm x 4mm, 0.8mm Thin QFN Package -40°C to +125°C Operation

MAX7312: Block Diagram Applications/Uses Instrumentation and Test Measurement Networking Medical Equipment RAID Systems Servers/Blades

DataSheet

Parametrics

Design kits & evaluation modules

• MAX7312EVKIT

Quality and Environmental Data

• MAX7312.pdf

Related Products

• MAX7318：2-Wire-Interfaced, 16-Bit, I/O Port Expander with Interrupt and Hot-Insertion Protection
• MAX7317：10-Port SPI-Interfaced I/O Expander with Overvoltage and Hot-Insertion Protection
• MAX6964：17-Output LED Driver/GPO with Intensity Control and Hot-Insertion Protection
• MAX7314：18-Port GPIO with LED Intensity Control, Interrupt, and Hot-Insertion Protection
• MAX7316：10-Port I/O Expander with LED Intensity Control, Interrupt, and Hot-Insertion Protection
• MAX7315：8-Port I/O Expander with LED Intensity Control, Interrupt, and Hot-Insertion Protection
• MAX7313：16-Port I/O Expander with LED Intensity Control, Interrupt, and Hot-Insertion Protection
• MAX6965：9-Output LED Driver with Intensity Control and Hot-Insertion Protection
• MAX7311：2-Wire-Interfaced 16-Bit I/O Port Expander with Interrupt and Hot-Insertion Protection
• MAX7310：2-Wire-Interfaced 8-Bit I/O Port Expander with Reset
• MAX7300：2-Wire-Interfaced, 2.5V to 5.5V, 20-Port or 28-Port I/O Expander
• MAX6956：2-Wire-Interfaced, 2.5V to 5.5V, 20-Port or 28-Port LED Display Driver and I/O Expander
• MAX7301：4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and 28-Port I/O Expander
• MAX6957：4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and 28-Port LED Display Driver and I/O Expander

Ordering Information